JCK-3自动升降建材可燃性试验炉

一、使用范围:

在老款产品基础上新增试样可控自动升降、本生灯可进退调节功能的升级产品，是严格依据国家标准GB8626-2007规定的而生产的的高配置建材燃烧等级测试仪器。

建材可燃性试验炉是在正常的燃烧环境中，用小火焰直接冲击垂直放置的试样以测定建筑制品可燃性。建材可燃性试验炉利用德国 Kleinbrenner（克莱因勃伦纳）原理，在垂直方向小火焰直接冲击下，用于测定B级建筑材料的燃烧性能（即用于建筑材料燃烧性能/阻燃等级B级的判定）。

1. Scope of use

On the basis of the old product, the upgraded product with controllable automatic lifting of the sample and the advance and retreat adjustment function of the Bunsen burner is added. It is a high-configuration building material combustion level test instrument produced in strict accordance with the national standard GB8626-2007.

The building material flammability test furnace uses a small flame to directly impact a vertically placed sample in a normal combustion environment to determine the flammability of building products. The building material flammability test furnace uses the German Kleinbrenner principle, under the direct impact of a small flame in the vertical direction, to determine the combustion performance of Class B building materials (that is, the combustion performance of building materials/flame retardant class B Level determination).

二、产品功能特点:

1.符合人机工程学的操作设计，试验全部通过触摸屏操作完成，自动化程度高，可存储以往试验结果，可调阅以往试验数据

2.伺服电机驱动式样架可控自动升降；

3.本生灯可进退调节；

4.1.5mm不锈钢钢板箱体；

5.2扇钢化耐热玻璃门双角度观察测试, 双（带锁）方便实用

6.高压自动点火，耐久燃烧；

7.点火源可自动倾斜45度；

8.火焰高度通过精密调节阀进行调节；

9.试样架可以上下及前后进行移动；

10.配备两种试样夹。

11.火焰测量标尺；

12.自动化程度高，实验数据精准、易操作；

13.箱体尺寸：94cmx40cmx80cm

14.材质：1.5mm不锈钢

15.箱体底部为平置自然通风口，通风口由5cm*5cm方格通风口组成(真正1.5mm厚钢板通风口,高50mm)保持气流平整通过

16.做工细致，真正无焊点工艺

17.触摸显示屏：

a. 尺寸：7寸 有效显示尺寸 长15.5cm 宽8.6cm；

b. 分辨率：800*480

c. 通讯接口 RS232、3.3V CMOS或TTL、串口方式

d. 储存容量:1G

e. 采用纯硬件FPGA驱动显示，“零”启动时间，上电即可运行

f. 采用M3+FPGA架构，M3负责指令解析，FPGA专注TFT显示，保障速度和可靠性 

g. 主控制器均采用低能耗处理器，自动进入节能模式

2. Product features

1. The operation design conforms to the ergonomics, all the tests are completed through the touch screen operation, the degree of automation is high, the past test results can be stored, and the past test data can be accessed

2. Servo motor-driven style rack can be controlled and automatically lifted;

3. The Bunsen burner can be adjusted forward and backward;

4.1.5mm stainless steel plate box;

5.2 Double-angle observation test of tempered heat-resistant glass doors, double (with lock) is convenient and practical

6. High-pressure automatic ignition, durable combustion;

7. The ignition source can automatically tilt 45 degrees;

8. The flame height is adjusted by a precision adjusting valve;

9. The sample holder can move up and down and back and forth;

10. Equipped with two sample holders.

11. Flame measurement scale;

12. High degree of automation, accurate experimental data and easy operation;

13. Box size: 94cmx40cmx80cm

14. Material: 1.5mm stainless steel

15. The bottom of the box is a flat natural vent, which is composed of 5cm*5cm square vents (real 1.5mm thick steel plate vents, height 50mm) to keep the airflow smoothly through

16. Meticulous workmanship, truly no solder joint process

17. Touch screen:

a. Size: 7 inches, the effective display size is 15.5cm in length and 8.6cm in width;

b. Resolution: 800*480

c. Communication interface RS232, 3.3V CMOS or TTL, serial port

d. Storage capacity: 1G

e. Use pure hardware FPGA to drive the display, "zero" startup time, and it can run after power-on

f. Adopt M3+FPGA architecture, M3 is responsible for instruction analysis, FPGA focuses on TFT display to ensure speed and reliability

g. The main controller adopts low-energy processors and automatically enters energy-saving mode

三、主要技术参数:

1. 环境温度：15℃～25℃；

2. 相对湿度：≤85％；

3. 供电电压和功率：220V    50HZ   100W；

4. 气源：纯度不低于95%的商用 ，普通试验也可用代替（涉及运输安全气源需用户自备）；

5. 本生灯对式样施加火焰时间15s

6.单片机控制，数字显示。

7.烧器孔径为Φ0.17mm、本生灯火焰长度20mm±2mm，燃烧器可倾斜45°。

8.对试样施加火焰(1s-99 s)±0.5s，可任意调节,精度±0.2s。

9.可燃气源：纯度95%以上的。

3. Main technical parameters

1. Ambient temperature: 15℃～25℃;

2. Relative humidity: ≤85%;

3. Supply voltage and power: 220V 50HZ 100W;

4. Gas source: commercial gas with a purity of not less than 95%, and ordinary tests can also be used instead (the user must prepare the gas source for transportation safety);

5. Bunsen burner applies flame to the pattern for 15s

6. Single-chip microcomputer control, digital display.

7. The burner aperture is Φ0.17mm, the Bunsen burner flame length is 20mm±2mm, and the burner can be tilted 45°.

8. Apply flame (1s-99 s) ±0.5s to the sample, which can be adjusted arbitrarily, with an accuracy of ±0.2s.

9. Combustible gas source: above 95% purity.