上海荣计达仪器科技有限公司

咨询电话:137-6111-8616


DM-III涂层打磨性测定仪

涂层打磨性测定仪是用于评价底漆、腻子打磨性优劣的装置。本装置对待测定的底漆、腻子试样进行来回打磨,打磨次数可由计数器直接读取,跟据负荷重量、打磨次数与磨损程度,可评定该底漆、腻子耐打磨的性能。本仪器采用磁性吸盘,试样装卸方便。

  • 型号: DM-III

  • 产品参数
  • 型号: DM-III

涂层打磨性测定仪是**检测仪器,是用于评价底漆、腻子打磨性优劣的装置。使用前务必仔细阅读说明书。并由**实验人员操作,以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。

The coating abrasiveness tester is a testing instrument, which is used to evaluate the superiority and inferiority of the abrasiveness of primer and putty. Be sure to read the instructions carefully before use. It is operated by ** experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.


涂层打磨性测定仪由上海荣计达仪器科技有限公司提供,设备质保期一年,一年内产品如有质量问题,供方负责免费维修。如果因操作不当或者人为损坏,我公司亦应提供维修、更换服务,由此产生的费用我公司会酌情收取。

The coating abrasiveness tester is provided by Shanghai Rongjida Instrument Technology Co., Ltd. The equipment warranty period is one year. If the product has quality problems within one year, the supplier is responsible for free maintenance. If due to improper operation or man-made damage, our company should also provide repair and replacement services, and the costs incurred by our company will be charged at our discretion.


涂层打磨性测定仪是用于评价底漆、腻子打磨性优劣的装置。本装置对待测定的底漆、腻子试样进行来回打磨,打磨次数可由计数器直接读取,跟据负荷重量、打磨次数与磨损程度,可评定该底漆、腻子耐打磨的性能。本仪器采用磁性吸盘,试样装卸方便。

Coating abrasiveness tester is a device used to evaluate the superiority and inferiority of primer and putty abrasiveness. The device polishes the primer and putty samples to be measured back and forth, and the number of times of grinding can be directly read by a counter. According to the load weight, the number of times of grinding and the degree of wear, the wear resistance of the primer and putty can be evaluated. The instrument uses magnetic chucks, which facilitates the loading and unloading of samples.


涂层打磨性测定仪主要参数:

★磨擦速度: 0~135次/分(单程)

★行程:130mm

★置数范围: 0~9999(双程计数)注:双程×2为单程

★荷重:打磨头:570±15克

         配重块:50±3克、70±3克、100±4克、200±7克,各1块

★电源: 220V  50Hz

★功率:60w

★外形尺寸:300×280×380mm 

★重量:约25kg

★样板规格:马口铁  50×120 δ=0.3~1.5mm

Main parameters of coating abrasiveness tester:

★ Friction speed: 0 ~ 135 times / minute (one way)

★ Stroke: 130mm

★ Setting range: 0 ~ 9999 (two-way counting) Note: two-way × 2 is one-way

★ Load: Polishing head: 570 ± 15g

          Counterweight: 50 ± 3g, 70 ± 3g, 100 ± 4g, 200 ± 7g, 1 each

★ Power supply: 220V 50Hz

★ Power: 60w

★ Dimensions: 300 × 280 × 380mm

★ Weight: about 25kg

★ Specifications: tinplate 50 × 120 δ = 0.3 ~ 1.5mm


涂层打磨性测定仪操作说明:

★顺时针旋转永磁吸盘边上的内六角扳手至“—”位置,将涂有试样并已干燥的50×120mm的马口铁板放在吸盘**,逆时针旋转内六角扳手至“+”位置,此时试样**被吸附在吸盘上了。

★将金相砂纸宽60×120mm作为打磨用砂纸,松开打磨头两旁锁紧螺母旋转紧纸圆柱(即中间开槽的轴棒),将打磨用砂纸收紧固定在打磨头上,然后旋紧锁紧螺母,再将打磨头放到本测定仪的摆臂上。如欲增加荷重量可将附加砝码置于打磨头上。

★插好电源,用置数器置数,选择欲磨擦的次数,通常置数为50(单程磨擦次数为100);转动调速旋钮,选择所需磨擦速度(推荐80次/分,)。

★打开电源开关,机器开始工作,到达预定次数后,机器自动停止,顺时针旋转内六角扳手至“—”位置,取下试样观察。

★机器运转中如欲停机可直接关闭电源开关,再要继续工作再打开电源开关即可。

★机器自动停止后,只需按置数器上的“清零(R)”按钮,机器即可再次运转。

Coating abrasiveness tester operating instructions:

★ Turn the Allen wrench on the side of the permanent magnet sucker clockwise to the “—” position, place the sample plate and dried 50 × 120mm tinplate in the center of the sucker, and turn the allen wrench counterclockwise to the “+” position. At this time, the sample ** is adsorbed on the suction cup.

★ Using metallographic sandpaper with a width of 60 × 120mm as the sanding sandpaper, loosen the lock nuts on both sides of the sanding head and rotate the tight paper cylinder (that is, the slotted shaft rod in the middle), tighten the sanding sanding paper on the sanding head, and then rotate Tighten the lock nut, and then place the grinding head on the swing arm of the analyzer. If you want to increase the load, put additional weight on the grinding head.

★ Plug the power, set it with the counter, select the number of times you want to rub, usually set to 50 (100 times for one-way friction); turn the speed control knob, select the desired friction speed (recommended 80 times / minute,)

★ Turn on the power switch and the machine will start to work. After reaching the preset number of times, the machine will stop automatically. Turn the hexagonal wrench clockwise to the "-" position, remove the sample for observation.

★ If the machine is to be stopped during operation, you can directly turn off the power switch, and then continue to work and then turn on the power switch.

★ After the machine stops automatically, just press the "Zero (R)" button on the counter, and the machine can run again.


打磨性测定仪注意事项:

1、未装试样和打磨砂纸时,严禁开机。

2、试验结束后应尽快切断电源

Note for abrasiveness tester:

1. It is strictly forbidden to start the machine when the sample and sanding paper are not installed.

2.The power should be cut off as soon as possible after the test.


DM-III涂层打磨性测定仪
涂层打磨性测定仪是用于评价底漆、腻子打磨性优劣的装置。本装置对待测定的底漆、腻子试样进行来回打磨,打磨次数可由计数器直接读取,跟据负荷重量、打磨次数与磨损程度,可评定该底漆、腻子耐打磨的性能。本仪器采用磁性吸盘,试样装卸方便。
长按识别二维码查看详情
长按图片保存/分享

DM-III涂层打磨性测定仪

询盘

咨询表单:

  • 请输入验证码

咨询内容:


你还没有添加任何产品

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

上海市闵行区浦江镇沈杜公路3259号                                                             网站地图

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

客服中心
热线电话
13761118616
上班时间
周一到周日
二维码
添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了