上海荣计达仪器科技有限公司

咨询电话:137-6111-8616


ZST-4砂浆充盈度试验仪

压浆剂充盈度测试仪符合铁道部行业标准管道压浆技术条件所规定试管直径和角度,充盈度判定:如果厚度超过1mm的泡沫层,或者存在大于3mm的气囊,或者存在体积大于1mmL的水,则判定充盈度指标不合格充盈度夹角120度,充盈度管内径∮40mm 长度500mm。

  • 型号: ZST-4

  • 产品参数
  • 型号: ZST-4

一、产品简介:研制出产符合铁道部行业标准管道压浆技能条件所规则试管直径和视点。符合铁道部行业标准管道压浆技术条件所规定试管直径和角度,充盈度判定:如果厚度超过1mm的泡沫层,或者存在大于3mm的气囊,或者存在体积大于1mmL的水,则判定充盈度指标不合格充盈度夹角120度,充盈度管内径∮40mm 长度500mm。

I. Product Description: Developed and produced the diameter and viewpoint of the test tube in accordance with the technical requirements of the Ministry of Railways. Comply with the diameter and angle of the test tube specified by the Ministry of Railways industry standard pipe grouting technology conditions, the degree of filling is judged: if the thickness of the foam layer exceeds 1mm, or there is a balloon larger than 3mm, or there is water with a volume greater than 1mmL, the filling degree is not determined. The acceptable filling angle is 120 degrees, and the filling tube inner diameter is 40mm and the length is 500mm.


二、充盈度断定:

假如厚度超越1mm的泡沫层,或许存在大于3mm的气囊,或许存在体积大于1mmL的水,则断定充盈度目标不合格充盈度夹角120°,充盈度管内径¢40mm 长度500mm。

Second, the filling degree is determined:

If the thickness exceeds 1mm of foam layer, there may be more than 3mm airbag, perhaps there is more than 1mmL of water, then the filling degree is unqualified, the filling angle is 120°, and the filling tube is ¢40mm and the length is 500mm.


三、技术参数:

★试管内径:40mm

★试管夹角:120°

★试管长度:0.5m*2

★试管原料:透明有机玻璃

★外形尺寸:100X100X300mm

★重量:3kg

Third, technical parameters:

★Test tube inner diameter: 40mm

★ test tube angle: 120 °

★Test tube length: 0.5m*2

★Test tube raw materials: transparent plexiglass

★Dimensions: 100X100X300mm

★ Weight: 3kg


四、使用方法:

★按规则的办法拌制好浆液

★将拌制好的浆液静置1min,

★通过活动锥,将浆液灌入固定在固定架上的充盈度管中

★充完浆液后,用塑料薄膜关闭圆管的两头。

★在20℃±3℃的条件下放置7d,

★7D后调查管内部是不是有直径大于3mm的气囊,或许是不是存在水囊或水蒸气,在管道的两头是不是有泡沫层。

Fourth, the method of use:

★ Mix the slurry according to the rules

★ Let the prepared slurry stand for 1 min.

★Pour the slurry into the filling tube fixed on the fixed frame through the movable cone

★ After filling the slurry, close the two ends of the tube with a plastic film.

★ placed at 20 ° C ± 3 ° C for 7d,

★ After 7D, investigate whether there are airbags with a diameter larger than 3mm inside the tube. Perhaps there is a water bladder or water vapor. Is there a foam layer at both ends of the pipe?


ZST-4砂浆充盈度试验仪
压浆剂充盈度测试仪符合铁道部行业标准管道压浆技术条件所规定试管直径和角度,充盈度判定:如果厚度超过1mm的泡沫层,或者存在大于3mm的气囊,或者存在体积大于1mmL的水,则判定充盈度指标不合格充盈度夹角120度,充盈度管内径∮40mm 长度500mm。
长按识别二维码查看详情
长按图片保存/分享

ZST-4砂浆充盈度试验仪

询盘

咨询表单:

  • 请输入验证码

咨询内容:


你还没有添加任何产品

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

上海市闵行区浦江镇沈杜公路3259号                                                             网站地图

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

客服中心
热线电话
13761118616
上班时间
周一到周日
二维码
添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了