欢迎访问上海荣计达仪器科技有限公司网站

热线电话:13761118616

图片展示

橡胶低温脆性试验机

橡胶低温脆性试验机是测定硫化橡胶在规定条件下试样受冲击出现破坏时的a高温度,即为脆性温度,可以对非硬质塑料及其他弹性材料在低温条件下的使用性能作比较性鉴定。

  • 型号: DWCX-70

  • 产品参数
  • 型号: DWCX-70

一、用途:

橡胶低温脆性试验机是测定硫化橡胶在规定条件下试样受冲击出现破坏时的a高温度,即为脆性温度,可以对非硬质塑料及其他弹性材料在低温条件下的使用性能作比较性鉴定。可以测定不同橡胶材料或不同配方的硫化橡胶的脆性温度和低温性能的优劣。因此无论在科学研究材料及其制品的质量检验,本仪器是根据GB/T 15256-1994《硫化橡胶低温脆性的测定(多试样法)》国家标准设计的,a新研制开发的压缩机制冷设备。本设备采用复叠式压缩机制冷技术,利用热平衡原理及循环搅拌方式,达到对试样的自动均匀冷却、恒温,可完全满足国家标准GB/T229-94做规定的各项控温指标。

First, use

The low-temperature brittleness tester for rubber is a high temperature when the vulcanized rubber is damaged by the impact under the specified conditions, that is, the brittle temperature, which can be used to compare the performance of non-hard plastics and other elastic materials under low temperature conditions. . The brittle temperature and low temperature properties of vulcanized rubbers of different rubber materials or different formulations can be determined. Therefore, no matter in the quality inspection of scientific research materials and their products, the instrument is designed according to the national standard GB/T 15256-1994 "Determining the low temperature brittleness of vulcanized rubber (multi-sample method)", a newly developed compressor refrigeration equipment . The equipment adopts the cascade compressor refrigeration technology, and uses the principle of heat balance and the circulating stirring method to achieve automatic uniform cooling and constant temperature of the sample, which can fully meet the various temperature control indexes stipulated by the national standard GB/T229-94.


二、技术参数:

■控温范围;0-60   0-70℃   

■降温速度:大约2小时左右

注:使用环境在室温下使用,工作时保持压缩机散温效果,可将侧门全部打开。

■恒温后,试验3min时间内温度波动:<±0.5℃

■a大外形尺寸:900×505×800mm(长×高×宽)

■工作室外形尺寸:200×140×100mm(长×高×宽) 

■冷却介质:乙醇或其他不冻液

■搅拌电机:10W

■工作电源220V~240V,50Hz,2kW

Second, technical parameters

■ Temperature control range; 0-60 0-70 °C

■ Cooling speed: about 2 hours

Note: The use environment is used at room temperature, and the compressor is kept warm while working, and the side door can be fully opened.

■ After constant temperature, the temperature fluctuation during the test within 3 minutes: <±0.5°C

■a large external dimensions: 900 × 505 × 800mm (length × height × width)

■Studio dimensions: 200 × 140 × 100mm (length × height × width)

■ Cooling medium: ethanol or other antifreeze

■Stirring motor: 10W

■Working power supply 220V~240V, 50Hz, 2kW


三、结构原理:

■本设备由制冷压缩机主机体、加热装置、电子控制箱、冷却槽、冷却介质循环系统、自动报警装置等部分组成。启动制冷开关后,压缩机开始工作,制冷系统进入正式工作状态。制冷压缩机连续不断的工作,当接近设定温度时,冷却槽中的加热装置开始按比例提供热量,用以平衡制冷系统产生的多余冷量,以达到恒温的目的。搅拌可使冷却槽内的冷却介质不断循环,使温度均匀一致。

■ 试样夹持器

试样一边夹持5个试样(橡胶类),另一边夹持15个试样(塑料类)。

■冲击装置

冲击装置由冲击锤和自锁机构组成。

■冲击器

冲击头半径为1.6±0.1mm;

冲击时,冲击头和试样夹持器之间间隙为6.4±0.3mm;

冲击头的中心线与试样夹持器之间的距离为8±0.3mm。

Third, the structure principle

■ This equipment consists of the main body of the refrigeration compressor, heating device, electronic control box, cooling tank, cooling medium circulation system, automatic alarm device and so on. After the cooling switch is activated, the compressor starts to work and the refrigeration system enters the official working state. The refrigeration compressor works continuously. When approaching the set temperature, the heating device in the cooling tank begins to provide heat proportionally to balance the excess cooling generated by the refrigeration system to achieve constant temperature. Stirring allows the cooling medium in the cooling tank to circulate continuously to make the temperature uniform.

■ Sample holder

The sample was sandwiched between five samples (rubber type) and the other side was clamped with 15 samples (plastic).

■ Impact device

The impact device consists of an impact hammer and a self-locking mechanism.

■ Impactor

The impact head radius is 1.6 ± 0.1 mm;

When impacting, the gap between the impact head and the sample holder is 6.4 ± 0.3 mm;

The distance between the center line of the impact head and the sample holder is 8 ± 0.3 mm.


橡胶低温脆性试验机
橡胶低温脆性试验机是测定硫化橡胶在规定条件下试样受冲击出现破坏时的a高温度,即为脆性温度,可以对非硬质塑料及其他弹性材料在低温条件下的使用性能作比较性鉴定。
长按识别二维码查看详情
长按图片保存/分享

橡胶低温脆性试验机

询盘

咨询表单:

  • 请输入验证码

咨询内容:


你还没有添加任何产品

加入成功

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

上海市闵行区浦江镇沈杜公路3259号                                                             网站地图

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了