欢迎访问上海荣计达仪器科技有限公司网站

热线电话:13761118616

图片展示

混凝土试件快速养护箱

混凝土快速养护箱是我公司依据行业标准T0509-94《水泥胶砂强度快速试验》设计制造。适用于水泥厂、建筑施工、科研等单位对普通硅酸盐水泥,矿渣水泥,火山灰水泥、粉煤灰水泥的试块进行快速养护。

  • 型号: HY-84A/B

  • 产品参数
  • 型号: HY-84A/B

一、混凝土快速养护箱是我公司依据行业标准T0509-94《水泥胶砂强度快速试验》设计制造。适用于水泥厂、建筑施工、科研等单位对普通硅酸盐水泥,矿渣水泥,火山灰水泥、粉煤灰水泥的试块进行快速养护。适用于水泥厂,建筑科研施工单位对所有混凝土试件进行快速恒温养护,可在24小时内预测出3天、7天、23天龄期的抗压、抗折试验结果,缩短水泥检验周期。

First, the concrete rapid curing box is designed and manufactured by our company in accordance with the industry standard T0509-94 "Quick Test of Cement Mortar Strength". It is suitable for cement plants, building construction, scientific research and other units to quickly maintain test blocks of ordinary portland cement, slag cement, pozzolan cement, and fly ash cement. It is suitable for cement plants, and the construction scientific research and construction units conduct rapid and constant temperature curing of all concrete specimens, and can predict the compression, flexural test results of 3 days, 7 days, and 23 days within 24 hours, shortening the cement inspection cycle.


二、混凝土快速养护箱技术参数:

★有效容积 0.12m3

★可放试块 150×150×150九块

★温控范围 室温—100℃

★温控精度 ±2℃

★温控方式 自动

★A长温控时间 9999min

★加热器总功率 10kW

★电源 AC380V 50HZ

★温控范围:室温0-100℃

★时间控制:0.5-24小时

★加热功率:1000W/220V

★内箱尺寸:A型:750mm×550mm×550mm(可放置2组混凝土试模)

          B型:550mm×350mm×320mm

Technical parameters of rapid concrete curing box:

★ Effective volume 0.12m3

★ Can put test block 150 × 150 × 150

★ Temperature control range

★ Temperature control accuracy ± 2 ℃

★ Temperature control method

A long temperature control time 9999min

★ Total heater power 10kW

★ AC380V 50HZ

★ Temperature control range: room temperature 0-100 ℃

★ Time control: 0.5-24 hours

★ Heating power: 1000W / 220V

★ Inner box size: Type A: 750mm × 550mm × 550mm (can put 2 sets of concrete test molds)

Type B: 550mm × 350mm × 320mm


三、混凝土快速养护箱使用方法:

★箱体安放平稳后,**先检查电器部分有无原件损坏,线路是否接触良好,插好传感器和加热器插头。设备必须有可靠接地。  

★开箱加水高约60mm。试块成型后,常温存放7小时或标养3小时,观察接近终凝时,(根据水泥成分不同,应自行注意观察,接近终凝时间)随同试模一起放入箱内搁架上。   

★盖好箱盖,插好温度传感器,根据各厂水泥成分不同,设定温度和工作时间。

★ 试验结束,取出试模放置常温处,到试块恢复常温时,拆开试模,取出试块,即可进行抗折、抗压试验。

★试验结束后,放水并擦干内箱。

★根据水泥种类不同,可采用恒温65-80℃之间进行,标准与快速对比试验10-20次,找出比值或差值,得出标准检验结果

★温度设定 

温控仪通电后,上排显示为当前箱体内温度,下排显示设定温度。此时,可用“∧”,“∨”键设定温度值。绿灯亮表示开始加温,闪烁表示恒温状态。 长期使用后,传感器出现零点漂移,当漂移超出试验要求范围,则需调整。具体操作如下:按下“SET”键3秒,温控仪进入参数调整状态,此时,上排显示所调整的项目,下排为对应数值,继续点动“SET”键,直到上排显示“SC”,此时可按“∧”,“∨”键,调整下排数值,进而修正正负偏差。其它参数不建议修改,如须修改,请参照所附温控表使用说明书。 

★混凝土快速养护箱时间设定 

接通电源后,4位数码管显示“00:00”,按“设置/查询”按钮,此时被设定位开始闪烁,可按“加数”按钮置数,按“移位”键可设定下一位数(从左到右)。设定好时间后按“启动”键,设备开始工作,计时从0开始,到达设定时间后,蜂鸣器响,提示保温时间到,可取出试块。试验中,当操作人员想查看设定时间为多少时,可按下“设定/查询”键,数码管显示设定时间,再次按下“设定/查询”键,设备继续工作,(查询后不能按“启动”键)。定时结束后按下“设定/查询”键即可令蜂鸣器停响。

Third, the use of rapid concrete curing box:

★ After the cabinet is installed smoothly, first check the electrical parts for damage to the original parts and whether the lines are in good contact. Plug the sensor and heater plugs. The equipment must be reliably grounded.

★ Unpacking and adding water is about 60mm high. After the test block is formed, it is stored for 7 hours at room temperature or 3 hours at standard temperature. When it is observed to be near the final setting, (depending on the composition of the cement, you should pay attention to it and approach the final setting time).

★ Close the lid of the box, insert the temperature sensor, and set the temperature and working time according to the cement composition of each plant.

★ After the test, remove the test mold and place it at normal temperature. When the test block returns to normal temperature, disassemble the test mold and remove the test block to perform the flexural and compressive test.

★ After the test, drain the water and dry the inner box.

★ Depending on the type of cement, constant temperature 65-80 ° C can be used. Standard and rapid comparison tests 10-20 times, find out the ratio or difference, and get the standard inspection results.

★ Temperature setting

After the temperature controller is powered on, the upper row shows the current temperature inside the cabinet, and the lower row shows the set temperature. At this time, you can use "∧" and "∨" keys to set the temperature value. The green light is on to indicate the start of heating, and the flashing indicates constant temperature. After long-term use, the sensor has zero drift. When the drift exceeds the range required by the test, it needs to be adjusted. The specific operation is as follows: Press the "SET" key for 3 seconds, the temperature controller enters the parameter adjustment state. At this time, the upper row displays the adjusted item, and the lower row is the corresponding value. Continue to jog the "SET" key until the upper row displays "SC", at this time, you can press the "∧" and "∨" keys to adjust the lower row value, and then correct the positive and negative deviation. It is not recommended to modify other parameters. If you need to modify, please refer to the instruction manual of the attached temperature control meter.

★ Time setting of rapid concrete curing box

After the power is turned on, the 4-digit digital tube displays "00: 00", and press the "Set / Query" button. At this time, the set bit starts to flash. You can press the "Add" button to set the number, and press the "Shift" key. Set the next digit (from left to right). After setting the time, press the "Start" key, the device starts to work, the timing starts from 0, when the set time is reached, the buzzer sounds, indicating that the holding time is up, you can remove the test block. In the test, when the operator wants to check the set time, he can press the "Set / Query" key, the digital tube displays the set time, press the "Set / Query" key again, the device continues to work, (Query You cannot press the "Start" key afterwards). After the timer is over, press the “Set / Query” button to stop the buzzer.


四、混凝土快速养护箱安全注意事项:

★加速养护箱盖在使用过程中请勿倒放(可依箱盖上提示标牌文字正视位置为准)。

★放置试件时应留测温探头的对应位置,以免探头插入时损坏。

★ 试件在放入和取出时一定要注意安全,即在使用专用工具钩起试件时必需确认工具钩是否已稳稳地钩牢试件,以防操作中途试件脱落箱内热水飞溅伤人。

★ 加速养护箱使用结束后必须切断电源,防止电热管无意中尚处于加热状态,造成脱水损机现象。

★加速养护箱长期不用时需将水放尽擦干,放在通风干燥处。

Fourth, safety precautions for rapid concrete curing box

★ Do not place the cover of the accelerated curing box upside-down during use (you can follow the position of the label on the box cover).

★ The corresponding position of the temperature probe should be kept when placing the test piece, so as to avoid damage when the probe is inserted.

★ When putting in and taking out the test piece, please pay attention to safety, that is, when using the special tool to hook up the test piece, you must confirm whether the tool hook has firmly hooked the test piece to prevent the test piece from falling off in the middle of operation. Hurt.

★ After the accelerated curing box is used, the power must be cut off to prevent the heating pipe from being inadvertently heated, which will cause dehydration and damage to the machine.

★ When the accelerating curing box is not used for a long time, it is necessary to dry the water thoroughly and put it in a dry and ventilated place.


五、混凝土快速养护箱结构:

箱体由内、外箱体和保温层组成。内外箱均采用优质不锈钢焊接成型。内外层之间填充有优质保温层。箱体与箱盖之间采用水槽密封。

Fifth, the rapid concrete curing box structure:

The box body is composed of an inner box and an outer box and an insulation layer. The inner and outer boxes are welded with high-quality stainless steel. The inner and outer layers are filled with a high-quality insulation layer. A water tank seal is used between the box body and the box cover.


混凝土试件快速养护箱
混凝土快速养护箱是我公司依据行业标准T0509-94《水泥胶砂强度快速试验》设计制造。适用于水泥厂、建筑施工、科研等单位对普通硅酸盐水泥,矿渣水泥,火山灰水泥、粉煤灰水泥的试块进行快速养护。
长按识别二维码查看详情
长按图片保存/分享

混凝土试件快速养护箱

询盘

咨询表单:

  • 请输入验证码

咨询内容:


你还没有添加任何产品

加入成功

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

上海市闵行区浦江镇沈杜公路3259号                                                             网站地图

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

客服中心
热线电话
13761118616
上班时间
周一到周日
二维码
添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了