上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

荣计达石膏板材厚度测定仪

用于测量石膏板材的厚度,也可用于测量其它材料的厚度,但需要根据所测材料和尺寸的不同要求,更换上下测头(本仪器不带附件)。如测钻头上螺旋槽的深度(用尖形测头);测木板、夹板、合成板等板材的厚度(用球形测头)。

  • 型号: BH-30

  • 产品参数
  • 型号: BH-30

 

石膏板材厚度测定仪**检测仪器,用于测量石膏板材的厚度,也可用于测量其它材料的厚度,但需要根据所测材料和尺寸的不同要求,更换上下测头(本仪器不带附件)。如测钻头上螺旋槽的深度(用尖形测头);测木板、夹板、合成板等板材的厚度(用球形测头)。

Gypsum board thickness tester is a testing instrument for measuring the thickness of gypsum board. It can also be used to measure the thickness of other materials. However, it is necessary to replace the upper and lower probes according to the different requirements of the measured material and size (this instrument does not have accessories) ). Such as measuring the depth of the spiral groove on the drill (using a pointed probe); measuring the thickness of wood, plywood, composite board and other plates (using a spherical probe).

 

石膏板材厚度测定仪主要技术参数:

测量范围:0-30mm

读出精度:0.01mm

握手架深度:116mm

净重:1.5kg

Main technical parameters of gypsum board thickness tester:

Measuring range: 0-30mm

Reading accuracy: 0.01mm

Handshake frame depth: 116mm

Net weight: 1.5kg

 

石膏板材厚度测定仪结构及工作原理

握手架开口端上边按了一个百分表。由螺钉锁紧:百分表原有球形测量头换上了盘形测量头,工作时压下百分表的上端压头,可使百分表上的测量杆也同时下降,松手后依靠百分表上面的弹簧复位。握手架开口端上边按了一个百分表,由螺钉锁紧,百分表原有球形测量杆也同时下降。松手后依靠百分表上面的弹簧复位。握手架开口端的下边按了一个测量头,下测量头靠M3推端紧定螺钉支撑及一个M3圆柱头螺钉拉紧,这样便于下测量头调整到与上测量头平行。

Structure and working principle of gypsum board thickness tester:

A dial indicator was pushed over the open end of the handshake. Tightened by screws: The original spherical measuring head of the dial indicator was replaced with a disc-shaped measuring head. When the upper end of the dial indicator is depressed during work, the measuring rod on the dial indicator can also be lowered at the same time. Spring return on the sub-meter. A dial indicator was pressed on the open end of the handshake frame and locked by screws. The original spherical measuring rod of the dial indicator was also lowered at the same time. After letting go, rely on the spring on the dial indicator to reset. A measuring head is pressed under the open end of the handshake frame. The lower measuring head is supported by the M3 pusher set screw and a M3 cylindrical head screw is tightened, so that the lower measuring head can be adjusted parallel to the upper measuring head.

 

石膏板材厚度测定仪操作使用与调整 使用前应检查百分表上的大小指针是否指向零位,这样可拧送螺钉调整百分表上下位置,然后旋紧,如大指针不在零位可转动百分表壳加以调整。

上下测量头接触时,侧面应全面接触,不应倾斜如有倾斜,可松动M3阀柱头螺钉,然后调整推端紧定螺钉使全面接触,然后将圆柱头螺钉拧紧即可。 测量板材厚度时,可将半才嵌入两端测量头之间,上下测量杆,使两测量头与板材紧密接触,此时即可在百分表上直接读出被测板材的厚度,小指针指的为毫米整数,大指针指的为小数。

Gypsum board thickness tester operation and adjustment Before use, check whether the size pointer on the dial indicator points to zero, so that you can screw in to adjust the upper and lower positions of the dial indicator, and then tighten, if the large pointer is not in the zero position, you can turn the 100 Adjust the case.

When the upper and lower measuring heads are in contact, the sides should be in full contact and should not be tilted. If it is tilted, loosen the M3 valve head head screw, then adjust the pusher set screw to make full contact, and then tighten the cylinder head screw. When measuring the thickness of the plate, you can insert half of it between the measuring heads at both ends, and then move the measuring rod up and down so that the two measuring heads are in close contact with the plate. At this time, the thickness of the measured plate can be read directly on the dial indicator. Refers to integers in millimeters and large pointers to decimals.

 

石膏板材厚度测定仪维护与保养

此仪器是精密量具,应轻拿轻放,禁止撞跌。使用完毕应用软布擦拭干净,妥为收藏,仪器平时不应随便拆卸,以免损坏。

Gypsum board thickness tester maintenance

This instrument is a precision measuring tool. After use, wipe it with a soft cloth and store it properly. The instrument should not be disassembled in order to avoid damage.


荣计达石膏板材厚度测定仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

荣计达石膏板材厚度测定仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号