上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

漆膜划痕试验仪

耐冲击性以及涂膜的滞留作用及清洗难易等,因此涂膜强度、硬度等是评价涂料性能的测指标。所以本仪器的用途即为通过漆膜样板涂层受划针刻划时抗穿透能力的大小来表征涂层强度、硬度、附着力的大小。

  • 型号: QHZ

  • 产品参数
  • 型号: QHZ

 

漆膜划痕试验仪**检测仪器,依照GB9279-88而设计制造。涂膜强度、硬度、附着力等是涂膜的重要的物理性能,其大小直接影响涂膜的重要使用性能,例如:耐磨损性;耐磨粒性;耐划痕性;耐冲击性以及涂膜的滞留作用及清洗难易等,因此涂膜强度、硬度等是评价涂料性能的测指标。所以本仪器的用途即为通过漆膜样板涂层受划针刻划时抗穿透能力的大小来表征涂层强度、硬度、附着力的大小。

Paint film scratch tester is a testing instrument designed and manufactured in accordance with GB9279-88. Coating film strength, hardness, adhesion, etc. are important physical properties of the coating film. Its size directly affects the important use properties of the coating film, such as: abrasion resistance; abrasion resistance; scratch resistance; The retention of the coating film and the difficulty of cleaning, etc., so the strength and hardness of the coating film are the measurement indicators for evaluating the performance of the coating. Therefore, the purpose of this instrument is to characterize the strength, hardness, and adhesion of the coating by the size of the anti-penetration ability when the coating of the paint film sample is scratched by the stylus.

 

漆膜划痕试验仪工作原理

本仪器主要是由划针架和工作台组成,划针架上的划针保证垂直地作用于涂膜样板上(样板固定在工作台上的实验台上,可横向或纵向移动;横向移动可为机动也可在关闭电源后手动,纵向移动为手动)。

在接通电源后,电源开关的红色指示灯亮说明仪器电源接通。此时如返程开关处于实验状态,工作台由右向左移动,划针在“实验”行程中和样板接触;返回行程(返程开关拨回“返回”状态)中,工作台由左向右移动,划针被抬起不接触样板,变换划针架上所加的砝码,可测出在不同重量下能否划破漆膜,用划破漆膜时所需的A小砝码重量来判断涂膜的抗划破性

Paint film scratch tester works:

This instrument is mainly composed of a needle holder and a workbench. The needle on the needle holder is guaranteed to act vertically on the coating film template (the sample is fixed on the experimental table on the workbench and can be moved horizontally or vertically; the horizontal movement can be For maneuvering, manual operation can also be performed after turning off the power, and vertical movement is manual operation).

After the power is turned on, the red indicator light on the power switch indicates that the instrument is powered on. At this time, if the return switch is in the experimental state, the table moves from right to left, and the stylus touches the sample during the "experiment" stroke; during the return stroke (the return switch is turned back to the "return" state), the table moves from left to right The needle is lifted without touching the template, and the weight added on the needle holder can be changed to determine whether the paint film can be broken under different weights. Use the small weight of A when the paint film is broken. Judge the scratch resistance of the coating film.

 

漆膜划痕试验仪技术指标

★划针长度不小于60mm      

★试验台移动速度:20—40mm/s

★划针针头钢球直径1mm     

★顶杠下端面的倾角:10—15°

★砝码加荷范围:0—2000g    

A小增量:50g

★工作电压::220V50HZ      

★消耗功率:15W

★重量:10Kg              

★外形尺寸:180*230*280mm

Technical index of paint film scratch tester:

★ Stitch length is not less than 60mm

★ Movement speed of test bench: 20-40mm / s

★ Stylus needle steel ball diameter 1mm

★ Inclination angle of the lower end of the top bar: 10-15 °

★ Weight loading range: 0-2000g

★ A small increment: 50g

★ Working voltage: 220V50HZ

★ Power consumption: 15W

★ Weight: 10Kg

★ Dimensions: 180 * 230 * 280mm

 

QHZ漆膜划痕试验仪使用要求

★涂膜样板:按GB9271—88制备,规格为:120*50mm

★实验环境:温度23±2°C,相对湿度:50±5%(参照GB9278—88)

QHZ paint film scratch tester requirements

★ Coated sample: prepared according to GB9271-88, specification: 120 * 50mm

★ Experimental environment: temperature 23 ± 2 ° C, relative humidity: 50 ± 5% (refer to GB9278—88)

 

QHZ漆膜划痕试验仪操作及使用方法

★准备

★按GB1727—79要求准备120*50mm(0.2—0.3mm厚)平滑马口铁或按展品规定要求的底板制备漆膜。

★检查仪器

1)接通电源(220V)

2)按下总开关(电源开关)然后拨动钮子开关至“实验”行程,试验台横向移动(向左)至左端停止,然后将钮子开关拨向“返回”行程,试验台横向移动(向右)至右端停止。注:钮子开关中间位置可急“停”。

3)按监测扭一下(点动)电表指针动,同时划破指示灯亮正常。

★在装划针处入一枚新划针,该划针应现用30倍放大镜检查针头,不得有划痕、园、锈斑等缺陷,划针安装的高低要适当。

★将样板夹入试验台的样板夹中,涂膜朝上,转动纵向手柄使试验台移至远端(试验台和工作台平齐)为初始位置。

★在砝码台上放入A小的砝码(50g)或予计划破涂膜的略小的负荷砝码。

QHZ paint film scratch tester operation and use method

★ Ready

★ Prepare 120 * 50mm (0.2-0.3mm thick) smooth tinplate according to GB1727-79 requirements or prepare paint film according to the requirements of exhibits.

★ Inspection equipment

(1) Turn on the power (220V)

(2) Press the main switch (power switch) and then turn the knob to the "Experiment" stroke. The test bench moves laterally (to the left) to the left end to stop, then turn the knob switch to the "Return" stroke. Move (to the right) to the right end to stop. Note: The middle position of the toggle switch can be “stopped” urgently.

(3) Press the monitor and twist (jog) the meter pointer to move, and at the same time, the indicator light is normal.

★ Insert a new stylus into the stylus. The stylus should be inspected with a 30x magnifying glass. There should be no defects such as scratches, gardens, rust spots, etc. The height of the stylus should be appropriate.

★ Clamp the sample plate into the sample plate of the test bench with the coating film facing upwards and turn the longitudinal handle to move the test bench to the far end (the test bench and the work bench are flush) as the initial position.

★ Put a small A weight (50g) or a slightly smaller load weight to break the coating film on the weight table.

 

QHZ漆膜划痕试验仪测试

★扳动工作钮开关至“实验”位置,划针在样板上划过,用眼观察是否划破,如划破时,电表指针动,同时划破指示灯亮,如未划破,扳工作开关至“返回”,使试验台返回停在右端,然后微动纵向移动手柄(正向旋进)使试验台移动一点(划出的**条划痕不至于重叠在A条划痕上即可),同时还需要把划针换一枚新的检查方法同前,并在砝码台上换上较重一个等级的砝码这**做好了划**条划痕的一切准备。

★重复上述的测试,直到划破涂膜为止(此时划破灯亮同时电表指针动,亦可用10倍放大镜观察划痕是否划破涂膜露出底板,划破部分的划痕长度应大于20mm)这时砝码的重量即为涂膜抗划值(该方法的测定值)。

★用该测定负荷对原先的样板及一块同样新的样板二者重复此测试步骤所得结果相符之后,则确定划透样板途程的,这A小负荷值为该种涂膜的抗划值。

当所测得负荷值不同时,则取三次的负荷值的平均值为该种涂膜的抗划值。

QHZ paint film scratch tester test

★ Toggle the work button switch to the "experimental" position, and then draw the needle across the template. Use your eyes to see if it is scratched. If you do, the meter pointer moves and the indicator light turns on. If it does not, flip the work switch. Go to "Return", make the test bench stop at the right end, and then slightly move the longitudinal movement handle (forward rotation) to move the test bench a little (the ** scratches drawn out will not overlap the A scratches. ) At the same time, you need to change the scratching needle to a new inspection method as before, and put a heavier weight on the weight table. This is all ready to scratch **.

★ Repeat the above test until the coating film is scratched (At this time, the light is on and the meter pointer moves. You can also use a 10x magnifying glass to observe whether the scratch has scratched the coating film and exposed the bottom plate. The length of the scratched part should be greater than 20mm) At this time, the weight of the weight is the scratch resistance value of the coating film (measured by this method).

★ After using this measurement load to repeat the test procedure for both the original sample and an equally new sample, it is determined that the sample passes through the course. The small load value of A is the anti-scratch value of the coating film.

When the measured load values are different, the average value of the three load values is taken as the scratch resistance value of the coating film.

 

QHZ漆膜划痕试验仪维护:

1、本仪器使用时力求转动灵活,应注意润滑(应在转动部位和不转动部位之间和相对运动部件之间注入机油);

2、本仪器在使用一段时间后,要全面检查紧固件,防止松动;

3、本仪器不使用时,要注意防尘、防潮、防腐蚀,避免振动和碰撞。

QHZ paint film scratch tester maintenance:

1. When using this instrument, strive to be flexible in rotation, and pay attention to lubrication (inject engine oil between rotating and non-rotating parts and between relatively moving parts);

2. After using the instrument for a period of time, check the fasteners thoroughly to prevent loosening;

3. When the instrument is not in use, pay attention to dust, moisture, and corrosion to avoid vibration and collision.

 

QHZ漆膜划痕试验仪附件配置

1、砝码一盒(一套):50g二件;100g二件;200g一件;500g三件。

2、放大镜二枚,30倍一枚;10倍一枚(自备)

3、划针一盒:20枚

QHZ paint film scratch tester accessories configuration

1. A box of weights (one set): two pieces of 50g; two pieces of 100g; one piece of 200g; three pieces of 500g.

2. Two magnifying glasses, one at 30 times; one at 10 times (provided)

3, a box of needles: 20


漆膜划痕试验仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

漆膜划痕试验仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号