上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

一次成型试模, 二次成型试模

用于工业与民用建筑砌墙砖抗压强度试验试样制备,使用前务必仔细阅读说明书。并由专业实验人员操作,以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。符合GB/T 2542-2012《砌墙砖试验方法》和GB/T 25044-2012《砌墙砖抗压强度试样制备设备通用要求》标准中抗压强度试验方法要求,分一次成型模具和二次成型模具两种。

  • 型号:ZW04

  • 产品参数
  • 型号:ZW04


 

一,一次成型试模, 二次成型试模产品概述:

用于工业与民用建筑砌墙砖抗压强度试验试样制备,使用前务必仔细阅读说明书。并由专业实验人员操作,以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。符合GB/T 2542-2012《砌墙砖试验方法》和GB/T 25044-2012《砌墙砖抗压强度试样制备设备通用要求》标准中抗压强度试验方法要求,分一次成型模具和二次成型模具两种。

First, the product overview:
For the preparation of test specimens for compressive strength of masonry bricks for industrial and civil buildings, please read the instructions carefully before use. It is operated by professional experimenters to avoid injury caused by improper operation. For more information, please contact our customer service staff. It meets the requirements of GB/T 2542-2012 "Test Method for Brick Wall Tiles" and GB/T 25044-2012 "General Requirements for Compressive Strength Specimen Preparation Equipment for Brick Wall Bricks", the requirements of compressive strength test method, one-time forming mold and two Two molding molds.

 

二,一次成型试模, 二次成型试模产品尺寸:

1、一次成型试模组装后型腔尺寸为:长120mm±15mm(可调节); 宽120mm±10mm(可调节);高115mm±5mm

2、二次成型试模组装后型腔尺寸为:长240mm±15mm(可调节); 宽120mm±10mm(可调节); 高65mm±5mm

Second, the product size:
1. The cavity size after one-time molding test is assembled: length 120mm±15mm (adjustable); width 120mm±10mm (adjustable); height 115mm±5mm
2. The size of the cavity after the assembly of the secondary molding test mode is: length 240mm±15mm (adjustable); width 120mm±10mm (adjustable); height 65mm±5mm

 

三,一次成型试模, 二次成型试模使用方法

1、一次成型试模组装后,用润滑油进行抹刷,然后把砖试样放入试模中,在中间和两边插入插板以确定厚度,前后方向用胶皮密封,初步拧紧螺丝固定试样,取出插板,A终拧紧螺丝。把固定好样品的试模放到振动台上加入专用净浆制样。

2、二次成型试模组装后,用润滑油进行抹刷,放入专用净浆材料,然后把砖试样放入试模中的顶丝上,顶丝保证净浆厚度不超过3mm,用螺丝把试样固定,放到振动台上进行振动,待净浆材料硬化后拆模重新对另一面进行加工。

Third, the method of use:
1. After assembling the primary test mold, brush with lubricating oil, then put the brick sample into the test mold, insert the insert plate in the middle and both sides to determine the thickness, seal the rubber in the front and rear direction, and initially tighten the screw. As such, remove the insert and tighten the screws at the end. Place the test piece with the sample fixed on the shaker table and add the special paste sample.
2. After the assembly of the secondary molding test, the brush is brushed with lubricating oil, and the special paste material is placed, and then the brick sample is placed on the top wire in the test mold, and the top wire ensures that the thickness of the paste does not exceed 3 mm. Fix the sample with screws and put it on the vibrating table to vibrate. After the pulp material is hardened, the mold is removed and the other side is processed.

 

四,一次成型试模, 二次成型试模保养:

试模使用结束后,把试模表面用铲刀清理干净,然后用润滑油进行涂涮,以方便下次使用。

Fourth, maintenance:
After the test pattern is used, clean the surface of the test mold with a blade and then apply it with oil to facilitate the next use.


一次成型试模, 二次成型试模

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

一次成型试模, 二次成型试模

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号