上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

石膏棱边深度测定仪

石膏板楔形棱边深度测定仪是专业石膏板检测仪器,用以测量纸面石膏板楔形棱边深度,符合GB/T9775-1999标准规定的纸面石膏板的试验方法。

  • 型号: XL-10

  • 产品参数
  • 型号: XL-10

 

石膏棱边深度测定仪是专业石膏板检测仪器,用以测量纸面石膏板楔形棱边深度,符合GB/T9775-1999标准规定的纸面石膏板的试验方法。使用前务必仔细阅读说明书。并由专业实验人员操作,以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。

The gypsum board wedge edge depth measuring instrument is a professional gypsum board testing instrument for measuring the depth of the wedge edge of the gypsum board and conforming to the test method of the gypsum board specified in GB/T9775-1999. Be sure to read the instructions carefully before use. It is operated by professional experimenters to avoid injury caused by improper operation. For more information, please contact our customer service staff.

 

石膏棱边深度测定仪技术参数:

1、测量范围:0-10mm

2、读出精度:0.01mm

3、定位舌与测量点距离:10mm

4、外形尺寸:260X120X160mm

5、重量:1.2kg

Gypsum board wedge edge depth measuring instrument technical parameters:
1, measuring range: 0-10mm
2, read accuracy: 0.01mm
3. Distance between positioning tongue and measuring point: 10mm
4, dimensions: 260X120X160mm
5, weight: 1.2kg

 

石膏棱边深度测定仪调整与操作:  

使用前,将仪器放在平板上面,左手适当用力按住仪器,使本体底面与平板紧密接触,定位舌及百分表测量杆手压缩入,然后适当松开螺钉(8)调节百分表上下位置,调整好后随即拧紧螺钉(8)锁紧百分表不再移动。并按百分表清零键,使百分表置零。接下来就可以进行使用测量。在每次使用前都必须将百分表清零(数显百分表使用见其说明书。)

Gypsum board wedge edge depth measuring instrument adjustment and operation:
Before use, place the instrument on the top of the plate, press the instrument with the left hand and press the instrument so that the bottom of the body is in close contact with the plate. The positioning tongue and the dial indicator are compressed by the hand. Then loosen the screw (8) and adjust the dial indicator. Position, adjust the screw and tighten the screw (8). The lock dial indicator no longer moves. And press the clear key to clear the dial indicator to zero. The measurement can then be used. The dial indicator must be cleared before each use (see the instructions for the use of the digital dialect.)

 

石膏棱边深度测定仪在进行测量时手持仪器本体,前端朝向石膏板棱边方向,按在石膏板上,同时慢慢向棱边方向移动,待定位舌伸出以后再将仪器稍稍往后移动,使定位舌紧紧靠棱边边缘,此时即可以从百分表上读出所测楔形棱边深度。在整个过程中,应尽量使仪器本体与石膏板棱边垂直,特别在读数时,否则会引起误差。

XL-10 gypsum board wedge edge measuring instrument holds the instrument body when measuring, the front end is facing the edge of the gypsum board, pressing on the gypsum board, and slowly moving in the direction of the edge, after the tongue is extended The instrument is moved slightly back so that the positioning tongue is pressed against the edge of the edge, and the measured wedge edge depth can be read from the dial indicator. In the whole process, the instrument body should be as perpendicular as possible to the edge of the plasterboard, especially when reading, otherwise it will cause errors.

 

石膏棱边深度测定仪维护保养:   

仪器是精密量具。应经常保持清洁,注意轻拿轻放,使用完毕应用软布擦拭干净。定位舌时间可适当加些润滑油,但不要过多,加润滑油后使定位舌上下活动几次,然后擦去多于润滑油,使活动面上面保留一层油膜即可,仪器平时不应随便拆卸,以免损坏。

XL-10 plasterboard wedge edge depth gauge maintenance:
The instrument is a precision measuring tool. Always keep it clean, take care to handle it gently, and wipe it clean with a soft cloth. When positioning the tongue time, you can add some lubricating oil properly, but don't overdo it. After adding the lubricating oil, make the positioning tongue move up and down several times, then wipe off more than the lubricating oil, so that the oil film can be left on the movable surface. The instrument should not be used normally. Feel free to disassemble to avoid damage.


石膏棱边深度测定仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

石膏棱边深度测定仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号