上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

打磨性测定仪

涂层打磨性测定仪是专业检测仪器,是用于评价底漆、腻子打磨性优劣的装置。

  • 型号:DM-III

  • 产品参数
  • 型号:DM-III


 

打磨性测定仪是专业检测仪器,是用于评价底漆、腻子打磨性优劣的装置。使用前务必仔细阅读说明书。并由专业实验人员操作,以避免操作不当引起的伤害。如需了解更多资料请与我公司客服人员联系。

The coating sanding tester is a professional testing instrument and is used to evaluate the quality of the primer and putty. Be sure to read the instructions carefully before use. It is operated by professional experimenters to avoid injury caused by improper operation. For more information, please contact our customer service staff.

 

打磨性测定仪由上海荣计达仪器科技有限公司提供,设备质保期一年,一年内产品如有质量问题,供方负责免费维修。如果因操作不当或者人为损坏,我公司亦应提供维修、更换服务,由此产生的费用我公司会酌情收取

The coating sanding tester is provided by Shanghai Rongjida Instrument Technology Co., Ltd. The equipment warranty period is one year. If the product has quality problems within one year, the supplier is responsible for free maintenance. If the operation is improper or man-made damage, our company should also provide repair and replacement services, and the expenses incurred by the company will be charged as appropriate.

 

打磨性测定仪是用于评价底漆、腻子打磨性优劣的装置。本装置对待测定的底漆、腻子试样进行来回打磨,打磨次数可由计数器直接读取,跟据负荷重量、打磨次数与磨损程度,可评定该底漆、腻子耐打磨的性能。本仪器采用磁性吸盘,试样装卸方便。

The coating sanding tester is a device for evaluating the quality of the primer and putty. The primer and the putty sample to be measured are polished back and forth, and the grinding times can be directly read by the counter, and the performance of the primer and the putty can be evaluated according to the load weight, the number of grinding times and the degree of wear. The instrument adopts a magnetic suction cup, and the sample is convenient to be loaded and unloaded.

 

打磨性测定仪主要参数:

★磨擦速度: 0~135次/分(单程)

★行程:130mm

★置数范围: 0~9999(双程计数)注:双程×2为单程

★荷重:打磨头:570±15克

         配重块:50±3克、70±3克100±4克、200±7克,各1块

★电源: 220V  50Hz

★功率:60w

★外形尺寸:300×280×380mm 

★重量:约25kg

★样板规格:马口铁  50×120 δ=0.3~1.5mm

The main parameters of the coating sanding tester:
★ Friction speed: 0~135 times/min (one way)
★Travel: 130mm
★Setting range: 0~9999 (two-way counting) Note: Two-way × 2 is one-way
★Load: Grinding head: 570±15g
          Weights: 50±3g, 70±3g, 100±4g, 200±7g, 1 each
★Power supply: 220V 50Hz
★Power: 60w
★Dimensions: 300 × 280 × 380mm
★ Weight: about 25kg
★Model specifications: tinplate 50×120 δ=0.3~1.5mm

 

打磨性测定仪操作说明:

★顺时针旋转永磁吸盘边上的内六角扳手至“—”位置,将涂有试样并已干燥的50×120mm的马口铁板放在吸盘中央,逆时针旋转内六角扳手至“+”位置,此时试样就被吸附在吸盘上了。

★将金相砂纸宽60×120mm作为打磨用砂纸,松开打磨头两旁锁紧螺母旋转紧纸圆柱(即中间开槽的轴棒),将打磨用砂纸收紧固定在打磨头上,然后旋紧锁紧螺母,再将打磨头放到本测定仪的摆臂上。如欲增加荷重量可将附加砝码置于打磨头上。

插好电源,用置数器置数,选择欲磨擦的次数,通常置数为50(单程磨擦次数为100);转动调速旋钮,选择所需磨擦速度(推荐80次/分,)。

打开电源开关,机器开始工作,到达预定次数后,机器自动停止,顺时针旋转内六角扳手至“—”位置,取下试样观察。

机器运转中如欲停机可直接关闭电源开关,再要继续工作再打开电源开关即可。

机器自动停止后,只需按置数器上的“清零(R)”按钮,机器即可再次运转。

Coating sanding tester operating instructions:
★ Turn the Allen key on the side of the permanent magnet chuck clockwise to the “—” position, place the 50×120mm tinplate coated with the sample and dry in the center of the suction cup, and turn the Allen key counterclockwise to the “+” position. At this point, the sample is adsorbed on the suction cup.
★Use the metallographic sandpaper width 60×120mm as the sanding paper for grinding, loosen the lock nut on both sides of the grinding head and rotate the tight paper cylinder (ie the axially slotted shaft rod), tighten the sanding paper to the grinding head, and then rotate Tightly lock the nut and place the sanding head on the swing arm of the analyzer. If you want to increase the load weight, you can place the additional weight on the sanding head.
★ Plug in the power supply, use the set number to set the number of times to be rubbed, usually set to 50 (one-way friction times is 100); turn the speed control knob to select the desired friction speed (recommended 80 times / min,).
★ Turn on the power switch, the machine starts working, after the predetermined number of times, the machine stops automatically, rotate the Allen key clockwise to the “—” position, and take off the sample to observe.
★ If you want to stop the machine during operation, you can directly turn off the power switch, and then continue to work and then turn on the power switch.
★After the machine stops automatically, just press the “Clear (R)” button on the register and the machine will run again.

 

打磨性测定仪注意事项:

1、未装试样和打磨砂纸时,严禁开机。

2、试验结束后应尽快切断电源

Precautions for the sanding tester:
1. It is strictly forbidden to start the machine when the sample is not loaded and the sandpaper is sanded.
2. The power should be cut off as soon as possible after the test


打磨性测定仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号