上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

AFA-II自动涂膜器

是专业涂膜仪器,方便地在不同的底材上自动完成湿膜制备器或线棒涂布器的涂布运动,避免了涂膜过程中的人为因素误差,能有效地提高制膜的重现性。

 

AFA-II自动涂膜器是专业涂膜仪器,方便地在不同的底材上自动完成湿膜制备器或线棒涂布器的涂布运动,避免了涂膜过程中的人为因素误差,能有效地提高制膜的重现性。

The automatic film coating machine is a professional film coating machine, which can automatically complete the coating movement of the wet film preparation device or the wire bar coater on different substrates, avoiding the human factor error in the coating process and effectively improving Reproducibility of film formation.

 

AFA-II自动涂膜器参数:

涂布底座尺寸:475mm×350mm

可真空尺寸;430mm×300mm

可涂布长度:250mm或370mm

涂布速率:0~10cm/s无极变速

总功率:350W

电源:220V 50Hz

外形尺寸:705mm×505mm×270mm (长×宽×高)

重量:约65Kg

AFA-II automatic film coating machine parameters:
★ Coating base size: 475mm × 350mm
★ vacuum size; 430mm × 300mm
★ coatable length: 250mm or 370mm
★ Coating rate: 0 ~ 10cm / s infinitely variable speed
★ Total power: 350W
★Power supply: 220V 50Hz
★Dimensions: 705mm × 505mm × 270mm (length × width × height)
★ Weight: about 65Kg

 

AFA-II自动涂膜器仪器特点

本设备采用无级变速电动机,精确控制涂布速率。

采用横杆推动湿膜制备器,对湿膜制备器的外形尺寸无特殊要求。

采用内置真空泵,方便本设备的携带及搬运。

放置在涂布器底座的左侧边缘的不锈钢废料收集盘,可收集多余的涂料,以确保设备本身及周围区域的清洁。

AFA-II automatic film coating machine features:
★ This equipment uses a continuously variable motor to precisely control the coating rate.
★The wet film preparation device is driven by the cross bar, and there is no special requirement for the outer dimensions of the wet film preparation device.
★ Built-in vacuum pump to facilitate the carrying and handling of this equipment.
★ A stainless steel waste collection tray placed on the left edge of the applicator base collects excess paint to ensure cleanliness of the unit itself and the surrounding area.

 

AFA-II自动涂膜器使用方法:

接好电源。

将待涂布底材(如:黑白纸)平放在涂布底座上,打开真空泵开关到“吸附”位置,这时,涂布底材即被吸附在涂布底座上了。(注意:当待涂布底材尺寸小于可真空尺寸时,应用其它纸张或用透明胶条遮盖多余的真空小孔,以免待涂布底材吸附不牢固,造成涂布失败)。

将横向推杆放置在涂布底座两侧的固定杆上。

选择适当的涂布长度,按下“复位”按钮,使横向推杆到达涂布的起始位置。

将湿膜制备器放置在横向推杆的前方。

选择适当的涂布速度。

直接在湿膜制备器前面放置适量的待涂布涂料。

按下“开始”按钮,开始涂布。

待涂布停止后,将剩余涂料刮入废料收集盘。

关闭真空泵,取下制好的样板,以待下次操作。

How to use AFA-II automatic film coating machine:
★ Connect the power supply.
★ Place the substrate to be coated (such as black and white paper) on the coating base and open the vacuum pump switch to the “adsorption” position. At this time, the coated substrate is adsorbed on the coating base. (Note: When the size of the substrate to be coated is smaller than the vacuumable size, apply other paper or cover the excess vacuum hole with a transparent strip to prevent the coated substrate from being adsorbed weakly, resulting in coating failure).
★ Place the lateral push rods on the fixing rods on both sides of the coating base.
★ Select the appropriate coating length and press the “Reset” button to bring the lateral pusher to the starting position of the coating.
★ Place the wet film preparation device in front of the lateral push rod.
★ Choose the appropriate coating speed.
★ Place an appropriate amount of the coating to be applied directly in front of the wet film preparation device.
★ Press the “Start” button to start coating.
★ After the coating stops, scrape the remaining paint into the waste collection tray.
★ Turn off the vacuum pump and remove the prepared sample for the next operation.

 

AFA-II自动涂膜器注意事项:

在设备运转过程中不能随便调节涂布长度的旋钮,否则会造成再次开机时滑杆不动作,一旦发生这种情况,可以把滑杆推到后,再开机,故障即可消除。

涂布底座应保持清洁,有杂物粘在上面,以免影响涂布底座的平面度,从而影响下次涂布;若不慎将涂料滴落在涂布底座上,也应及时清洁。

定时检查油杯油位,若发现油位不够,则应及时加入润滑油,以润滑导轨。

每次使用本设备后,应用防尘罩遮盖,以免灰尘掉入真空小孔,并被真空泵吸入,影响其使用寿命。

每次使用本设备后,应及时清洗废料收集盘。

AFA-II automatic film coating machine notes:
★ The knob of the coating length cannot be adjusted randomly during the operation of the device. Otherwise, the slider will not move when the machine is turned on again. Once this happens, the slider can be pushed to the rear and then turned on, and the fault can be eliminated.
★The coating base should be kept clean, and the sundries stick to it, so as not to affect the flatness of the coating base, thus affecting the next coating; if the paint is dropped on the coating base, it should be cleaned in time.
★ Check the oil level of the oil cup regularly. If the oil level is not enough, you should add the lubricating oil in time to lubricate the guide rail.
★After using the device, cover it with a dust cover to prevent dust from falling into the vacuum hole and being sucked in by the vacuum pump, which will affect its service life.
★ After each use of this equipment, the waste collection tray should be cleaned in time.

 

AFA-II自动涂膜器装箱单:

A:主机               1台

B:附件.

1.横向推杆           1根

2.线棒夹具           1根

3.废料收集盘         1只

4.说明书             1本

5.产品合格证         1份

AFA-II automatic film coating machine packing list:
A: Host 1
B: Attachment.
1. Horizontal push rod 1
2. Wire rod fixture 1
3. Waste collection tray 1
4. Manual 1
5. Product certificate 1 copy


AFA-II自动涂膜器

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号