上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

混合料霹裂试验仪

沥青混合料劈裂试验仪是专业沥青检测仪器,用于测定沥青混合料在规定温度和加载速率时劈裂破坏或处于弹性阶段的力学性质,亦可供沥青路面结构设计选择沥青混合料力学设计参数及评价沥青混合料低温抗裂性能时使用。

  • 型号:SYD-0716

  • 产品参数
  • 型号:SYD-0716

 

混合料劈裂试验仪是专业沥青检测仪器,用于测定沥青混合料在规定温度和加载速率时劈裂破坏或处于弹性阶段的力学性质,亦可供沥青路面结构设计选择沥青混合料力学设计参数及评价沥青混合料低温抗裂性能时使用。

Asphalt mixture splitting tester is a professional asphalt testing instrument used to determine the mechanical properties of asphalt mixture in the cracking failure or in the elastic stage at the specified temperature and loading rate. It can also be used to design the asphalt pavement structure. Use parameters and evaluate the low temperature crack resistance of asphalt mixtures.

 

混合料劈裂试验仪技术指标:

上升速率:(50±5)mm/min

压条直径:(101.6±0.2)mm (152.4±0.2)mm

大压力: 50KN 精度 1%

位移测量范围:0-15mm 分辨率:0.01mm 精度 ±0.1mm

外形尺寸: 650x480x900mm

环境温度:≤30℃

相对湿度:≤85%

整机功耗:750W

仪器净重:100kg

电源电压:220v

SYD-0716 asphalt mixture splitting tester technical indicators:
★Rising rate: (50±5)mm/min
★Beet diameter: (101.6±0.2)mm (152.4±0.2)mm
★High pressure: 50KN Accuracy 1%
★ Displacement measurement range: 0-15mm Resolution: 0.01mm Accuracy ±0.1mm
★Dimensions: 650x480x900mm
★ Ambient temperature: ≤30°C
★ Relative humidity: ≤85%
★Power consumption of the whole machine: 750W
★ Instrument net weight: 100kg
★Power supply voltage: 220v

 

混合料劈裂试验仪特点:

设有过载保护,下降过位保护。

操作简便,测试数据准确,性能稳定可靠。

仪器自动试验,显示并打印,绘制试件受力变形的坐标曲线图。

可存储15组试件的试验结果。

大型液晶屏显示曲线和稳定度及流值。

流值检测有单路与双路两种。

试验由仪器或计算机自动控制,试件受压变形过程数据及曲线由计算机自动存盘并显示,可通过打印机打印输出。

先进的自动分析软件,按照《沥青混合料配合比设计方法》绘制出各种曲线,自动给出A佳沥青用量,可通过打印机输出。

带有上位机软化可以通过强大的实验软件进行分析处理。

Asphalt mixture splitting tester features:
★ With overload protection, drop over position protection.
★ Easy to operate, accurate test data, stable and reliable performance.
★ The instrument automatically tests, displays and prints, and draws the coordinate curve of the specimen under stress deformation.
★ The test results of 15 sets of test pieces can be stored.
★ Large LCD screen shows curve and stability and flow value.
★ There are two types of flow detection: single and double.
★The test is automatically controlled by the instrument or computer. The data and curve of the test piece under pressure deformation are automatically saved and displayed by the computer, which can be printed out by the printer.
★Advanced automatic analysis software, according to the "asphalt mixture mix design method" draws various curves, automatically gives A good asphalt dosage, which can be output through the printer.
★ With the upper machine softening can be analyzed and processed by powerful experimental software.

 

混合料劈裂试验仪适用范围:

适用于测定沥青混合料在规定温度和加载速率时劈裂破坏或处于弹性阶段的力学性质,亦可供沥青路面结构设计选择沥青混合料力学设计参数及评价沥青混合料低温抗裂性能时使用。试验温度与加载速率可由当地气候条件根据试验目的或有关规定选用,但试验温度不得高于30℃,如无特殊规定,宜采用试验温度15℃±0.5℃,加载速率为50mm/min。当用于评价沥青混合料低温抗裂性能时,宜采用试验温度-10℃±0.5℃及加载速率1mm/min。

SYD-0716 asphalt mixture splitting tester scope:
It is suitable for determining the mechanical properties of asphalt mixture in the cracking failure or in the elastic stage at the specified temperature and loading rate. It can also be used in the asphalt pavement structure design to select the asphalt mixture mechanical design parameters and evaluate the low temperature crack resistance of the asphalt mixture. The test temperature and loading rate may be selected according to the local climatic conditions according to the test purpose or relevant regulations, but the test temperature shall not be higher than 30 °C. If there is no special regulation, the test temperature should be 15 °C ± 0.5 °C, and the loading rate is 50 mm/min. When used to evaluate the low temperature crack resistance of asphalt mixture, the test temperature is -10 ° C ± 0.5 ° C and the loading rate is 1 mm / min.

 

混合料劈裂试验仪本方法测定时采用沥青混合料的泊松比μ值如表1所示,其它试验温度的μ值由内插法决定。本方法也可由试验实测的垂直变形及水平变形计算实际的μ值,但计算的μ值必须在0.2~0.5范围内。

试验温度(℃) ≤10 15 20 25 30 泊松比μ值 0.25 0.30 0.35 0.40 0.45 本方法采用的圆柱体试件应符合下列要求:

A大粒径不超过26.5mm(圆孔筛30mm)时,用马歇尔标准击实法成型的直径为φ101.6mm±0.25mm试件,高为63.5mm±1.3mm。

从轮碾机成型的板块试件或道路现场钻取直径φ100mm±2mm或φ150mm±2.5mm,高为40mm±5mm的圆柱体试件。

SYD-0716 Asphalt Mixture Splitting Tester The Poisson's ratio μ value of the asphalt mixture used in this method is shown in Table 1. The μ values of other test temperatures are determined by interpolation. The method can also calculate the actual μ value from the measured vertical deformation and horizontal deformation, but the calculated μ value must be in the range of 0.2 to 0.5.
Test temperature (°C) ≤10 15 20 25 30 Poisson's ratio μ value 0.25 0.30 0.35 0.40 0.45 The cylindrical test piece used in this method shall meet the following requirements:
When the A large particle size does not exceed 26.5 mm (30 mm round hole sieve), the diameter of the test piece formed by the Marshall standard compaction method is φ101.6 mm±0.25 mm, and the height is 63.5 mm±1.3 mm.
A cylindrical test piece having a diameter of φ100 mm±2 mm or φ150 mm±2.5 mm and a height of 40 mm±5 mm was drilled from a plate test piece or a road formed by a wheel mill.

 

混合料劈裂试验仪仪具与材料:

试验机:能保持规定加载速率的材料试验机,也可采用马歇尔试验仪。试验机负荷应满足A大测定荷载不超过其量程的80%且不小于其量程的20%的要求,宜采用40kN或60kN传感器,读数精密度为10N。

恒温水箱:能保持温度为—18℃,当缺乏专用的恒温冰箱时,可采用家用电冰箱的冷冻室代替,控温准确度为2℃。 恒温水槽:用于试件保温,温度范围能满足试验要求,控温准确度为0.5℃。

压条:上下各一根,试件直径100mm时,压条宽度为12.7mm,内侧曲率半径50.8mm,压条两端均应磨圆。

劈裂试验夹具:下压条固定在夹具上,压条可上下自由活动。

其它:塑料袋、卡尺、天平、记录纸、胶皮手套等。

SYD-0716 asphalt mixture splitting tester instrument and materials:
Testing machine: A material testing machine capable of maintaining a specified loading rate, or a Marshall tester. The test machine load should meet the requirements of A large measurement load not exceeding 80% of its range and not less than 20% of its range. It is recommended to use 40kN or 60kN sensor with a precision of 10N.
Constant temperature water tank: It can keep the temperature at -18 °C. When there is no special constant temperature refrigerator, it can be replaced by the freezer of the household refrigerator. The temperature control accuracy is 2 °C. Constant temperature water tank: used for the insulation of test pieces, the temperature range can meet the test requirements, and the temperature control accuracy is 0.5 °C.
Binder: one on top of the other, when the test piece has a diameter of 100mm, the bead width is 12.7mm, the inner radius of curvature is 50.8mm, and both ends of the bead should be rounded.
Splitting test fixture: The lower bead is fixed on the fixture, and the bead can move freely up and down.
Others: plastic bags, calipers, balances, recording paper, rubber gloves, etc.


混合料霹裂试验仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

混合料霹裂试验仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号