上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

沥青标准粘度试验仪

沥青标准粘度计适用于沥青标准粘度试验(道路沥青标准粘度计法)本方法采用道路沥青标准粘度计测定液体石油沥青、煤沥青、乳化沥青等材料流动状态时的粘度。

  • 型号: SYD-0621A

  • 产品参数
  • 型号: SYD-0621A



沥青标准粘度计适用沥青标准粘度试验(道路沥青标准粘度计法)本方法采用道路沥青标准粘度计测定液体石油沥青、煤沥青、乳化沥青等材料流动状态时的粘度。本法测定的粘度应注明温度及流孔孔径,以CT.d表示(T为试验温度,C;d为孔径,mm)。

Asphalt standard viscometer is suitable for asphalt standard viscosity test (road asphalt standard viscometer method). This method uses road asphalt standard viscometer to measure the viscosity of liquid petroleum asphalt, coal asphalt, emulsified asphalt and other materials in the flowing state. The viscosity measured by this method should indicate the temperature and the pore size of the orifice, expressed in CT.d (T is the test temperature, C; d is the pore size, mm).

 

沥青标准粘度计特点:

数显智能表控温,。

循环水泵控制水循环。

控温范围:室温-90℃

设有冷光照明。

Asphalt Standard Viscometer Features:

★ Digital display intelligent temperature control.

★ Circulating water pump controls water circulation.

★ Temperature control range: room temperature-90 ℃

★ With cold light lighting.

 

沥青标准粘度计技术参数:

泻油孔直径(mm):   10±0.25       5±0.10       3±0.06

泻油孔高度(mm):      5             7             7

控温精度:     ± 0.5℃

恒温槽:″Φ160mmX100mm

盛样管:内径Φ40

外形尺寸:460X290X450mm

重量:9KG

电源电压:220V

功率:700W

环境温度:5~40℃

环境湿度:≦85﹪

Technical parameters of asphalt standard viscometer:

★ Diaphragm hole diameter (mm): 10 ± 0.25 5 ± 0.10 3 ± 0.06

★ Effusion hole height (mm): 5 7 7

★ Temperature control accuracy: ± 0.5 ℃

★ Thermostatic bath: "Φ160mmX100mm

★ Sample tube: inner diameter Φ40

★ Dimensions: 460X290X450mm

★ Weight: 9KG

★ Power supply voltage: 220V

★ Power: 700W

★ Ambient temperature: 5 ~ 40 ℃

★ Ambient humidity: ≦ 85 ﹪

 

沥青标准粘度计仪具与材料:

一,道路沥青标准粘度计:由下部分组成:

 水槽:环槽形,内径160mm,深100mm,有一圆井,井壁与水槽之间距离不少于55mm。环槽中存放保温用液体(水或油),上下方各设有A水管。水槽底离试验台面约200mm。水槽控温精密度±0.2℃。

盛样管:管体为黄铜而带流孔的底板为磷青铜制成。盛样管的流孔d有3mm±0.025mm、4mm±0.025mm、5mm±0.025mm和10mm±0.025四种。根据试验需要,选择盛样光流孔的孔径。

球塞:用以堵塞流孔,杆上有一标记。球塞直径12.7mm±0.05mm的标记高为92mm±0.25mm,用以指示10mm盛样管内试样的高度,球塞直径6.35mm±0.05mm的标记高为90.3mm±0.25mm,用以指示其它盛样管内试样的高度。

 水槽盖:盖的有套筒,可套在水槽的圆井上,下附有搅拌叶,盖上有一把手,转动把手时可借搅拌叶调匀水槽内水温。盖上还有一插孔,可放置温度计。

 温度计:分度为0.1℃。

接受瓶:开口,圆柱形玻璃容器,100mL,在25mL、50mL、75mL、100mL处有刻度;也可采用100mL量筒。

 流孔检查棒:磷青铜制,长100mm,检查4mm和10mm流孔及检查3mm和5mm流孔各一支,检查段位于两端,长度不少于10mm,直径按流孔下限尺寸制造。

 秒表:分度0.1s。

 循环恒温水槽。

 肥皂水或矿物油。

 其它:加热炉、大蒸发皿等。

Asphalt standard viscometer instruments and materials:

I. Road asphalt standard viscometer: It consists of the following parts:

★ Water trough: ring trough, inner diameter 160mm, depth 100mm, there is a round well in the middle, the distance between the well wall and the water trough is not less than 55mm. The ring tank stores liquid (water or oil) for heat preservation, and A water pipes are arranged on the upper and lower sides. The bottom of the water tank is about 200mm from the test bench. Water tank temperature control precision ± 0.2 ℃.

★ Sample tube: The tube body is brass and the bottom plate with flow holes is made of phosphor bronze. There are four orifices d in the sample tube: 3mm ± 0.025mm, 4mm ± 0.025mm, 5mm ± 0.025mm, and 10mm ± 0.025. According to the needs of the experiment, choose the aperture of the sample optical flow hole.

★ Ball plug: used to block the flow hole, there is a mark on the rod. The diameter of the ball plug with a diameter of 12.7mm ± 0.05mm is 92mm ± 0.25mm, which indicates the height of the sample in the 10mm sample tube. The diameter of the ball plug with a diameter of 6.35mm ± 0.05mm is 90.3mm ± 0.25mm, which indicates The height of other samples in the sample tube.

★ Sink cover: There is a sleeve in the cover, which can be sleeved on the round well of the sink. There is a stirring blade under the cover. There is a handle on the cover. When you turn the handle, you can use the stirring blade to adjust the water temperature in the sink. There is also a socket for the thermometer.

★ Thermometer: The division is 0.1 ℃.

★ Receiving bottle: Open, cylindrical glass container, 100mL, there are graduations at 25mL, 50mL, 75mL, 100mL; 100mL graduated cylinder can also be used.

★ Orifice inspection rod: made of phosphor bronze, 100mm in length, inspecting 4mm and 10mm orifices and inspecting 3mm and 5mm orifices, the inspection section is located at both ends, the length is not less than 10mm, and the diameter is manufactured according to the lower limit of the orifice.

★ Stopwatch: 0.1s division.

★ Circulating constant temperature water tank.

★ Suds or mineral oil.

★ Others: heating furnace, large evaporation dish, etc.

 

沥青标准粘度计使用方法和注意事项:

 本试验仪应水平放置于工作台面上,室温0~30℃,相对湿度不超过80%,无震动,无腐蚀性气体,且有良好的接地保护。

 使用前,先在恒温水浴内注入A的自来水,水位高度约为离上平面 15mm,用随机软管把两台仪器连接成一体。

 把两台仪器都插上电源(220V,50Hz),先启动恒温水浴部分的电源开关,按照温度控制器的使用说明书调节温度到所需要的值,启动加热和搅拌开关,经过一段时间后,**能达到所需的温度值。

 设置好恒温水浴部分后,然后开启真空度控制部分的电源开关。当电源开关打开后,真空泵直接开始工作,使用者可根据真空表说明书设定真空度(一般情况下,出厂时已经为用户进行了设置,不需重新设置)。根据表上的数值,慢慢地用调压阀调节真空度,这个过程须经过几次反复。(此时必须关闭连接毛细管的阀门)。

 试验过程中,打开照明开关,以便清晰观察整个试验过程。

Asphalt standard viscometer use method and precautions:

★ The tester should be placed horizontally on the work surface, room temperature 0 ~ 30 ℃, relative humidity not exceeding 80%, no vibration, no corrosive gas, and good grounding protection.

★ Before use, inject the tap water of A in the constant temperature water bath, the water level is about 15mm from the upper plane, and connect the two instruments into one with a random hose.

★ Plug both instruments into the power supply (220V, 50Hz), first turn on the power switch of the constant temperature water bath part, adjust the temperature to the required value according to the instruction manual of the temperature controller, and start the heating and stirring switch. ** Able to reach the required temperature value.

★ After setting the constant temperature water bath part, then turn on the power switch of the vacuum degree control part. When the power switch is turned on, the vacuum pump starts to work directly, and the user can set the vacuum degree according to the manual of the vacuum gauge. According to the value on the table, slowly adjust the vacuum with the pressure regulating valve. This process must be repeated several times. (The valve connecting the capillary must be closed at this time).

★ During the test, turn on the light switch to clearly observe the entire test process.







沥青标准粘度试验仪

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

沥青标准粘度试验仪

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号