上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

混凝土振实台

混凝土振实台采用高频振动铜芯电机,框架采用加厚钢板焊接,表面喷涂,适用于试验室,现场工地作试件成型和预制构件震实各种板柱、梁等混凝土构件振实成型。

  • 型号:ZHJ-1

  • 产品参数
  • 型号:ZHJ-1

 

一,混凝土振实台产品简介:

混凝土振动台采用高频振动铜芯电机,框架采用加厚钢板焊接,表面喷涂,适用于试验室,现场工地作试件成型和预制构件震实各种板柱、梁等混凝土构件振实成型。混凝土振动台由台底架、振动器弹簧等部件组成,台面与底架均用钢板和型钢焊接而成,振动台是用电动机 加一对相同的偏心轮组成。并通过一对吊架联轴器安装在台面(反面)中心位置,起着振实过程中平稳、垂直方向的作用。符合 GB/T13309,IEC68-2-6(FC)等国家标准。

First, the concrete shaker product introduction:
The concrete vibrating table adopts high-frequency vibrating copper-core motor. The frame is welded with thick steel plate and surface sprayed. It is suitable for the test room. The site construction is used for test piece forming and prefabricated components to shake various concrete members such as slab columns and beams. The concrete vibration table is composed of a bottom frame and a vibrator spring. The table and the bottom frame are welded by steel plates and steel sections. The vibration table is composed of a motor and a pair of identical eccentric wheels. It is installed in the center of the table (reverse surface) through a pair of hanger couplings, and plays a role in the smooth and vertical direction during the tapping process. It complies with national standards such as GB/T13309 and IEC68-2-6 (FC).

 

二,混凝土振实台工作原理

混凝土振动台主要由台底架、振动器弹簧等部件组成,台面与底架均用钢板和型钢焊接而成,振动台是用电动机 加一对相同的偏心轮组成。并通过一对吊架联轴器安装在台面(反面)中心位置,起着振实过程中平稳、垂直方向的作用。

振动台符合 GB/T13309,IEC68-2-6(FC)等国家标准。

Second, the working principle of concrete shaking table
The concrete vibration table is mainly composed of a bottom frame and a vibrator spring. The table and the bottom frame are welded by steel plates and steel sections. The vibration table is composed of a motor and a pair of identical eccentric wheels. It is installed in the center of the table (reverse surface) through a pair of hanger couplings, and plays a role in the smooth and vertical direction during the tapping process.
The vibration table complies with national standards such as GB/T13309 and IEC68-2-6 (FC).

 

三,混凝土振实台技术参数:

★台面尺寸:500*500mm型;800*800 mm型;1000*1000mm型

★震动台频率:2860次/分 

★振幅:0.3-0.6mm  

★电机功率:1.5千瓦 380V 1千瓦 380V 0.75千瓦 380V

★定做震动台常用功率 2.1千瓦 380V 2.5千瓦 380V 1千瓦 220V

Third, the concrete shaking table technical parameters:
★ Table size: 500*500mm type; 800*800 mm type; 1000*1000mm type
★ Vibration station frequency: 2860 times / min
★Amplitude: 0.3-0.6mm
★Motor power: 1.5 kW 380V 1 kW 380V 0.75 kW 380V
★Customized vibration table common power 2.1 kW 380V 2.5 kW 380V 1 kW 220V

 

四,混凝土振实台使用说明:

★振动台安装前,应先打好基础,打基础时上平面要按水平找并按底梁螺栓孔埋好固定螺栓,然后安装, 安装时固定螺栓必须拧紧。

★振动台安装完毕试车前,先开车3—5分钟后停车,对所有紧固螺栓进行检查,若松动须拧紧后方可使用。

★振动台布振实过程中,混凝土制品应牢固的紧固在振动台面上,所需振实的制品放置要与台面对称,使负荷平衡,振实制品的紧固装置用户可根据自己的需求自行设计配制。

★振动器轴承应经常检查,并定期拆洗,更换润滑油,使轴承保持良好的润滑,延长振动器的使用寿命。

★振动台应有可靠的接地线,确保安全。

Fourth, concrete vibration table instructions:
★ Before the installation of the vibrating table, the foundation should be laid. When the foundation is hit, the upper plane should be found horizontally and the fixing bolts should be buried according to the bolt holes of the bottom beam, and then installed. The fixing bolts must be tightened during installation.
★Before installing the vibrating table, drive for 3-5 minutes and then stop. Check all the fastening bolts. If it is loose, it must be tightened before use.
★ During the vibration table vibration, the concrete products should be firmly fastened on the vibration table. The required products should be placed symmetrically with the table top to balance the load. The fastening device of the vibrating product can be customized according to your own needs. Design and formulation.
★Vibrator bearings should be inspected frequently, and regularly removed and replaced, and the lubricant should be replaced to keep the bearings well lubricated and prolong the service life of the vibrators.
★ The vibration table should have a reliable grounding wire to ensure safety.

 

五,混凝土振实台操作规程:

★振动台使用前需试车,先开车空载3~5min,停车拧紧全部紧固零件,反复2~3次,才能正式投入运转使用。

★ 振动台在生产使用中,混凝土试件的试模必须牢固地紧固在工作台上,试模的放置必须与台面的中心线相对称,使负载平衡。

★振动电机应有良好的可靠的地线。

★振动台在生产过程中如发现噪音不正常,应立即停止使用,拔去电源全面检查紧固零件是否松动,必要时要检查振动电机内偏心块是否松动或零件损坏,拧紧松动零件,调换损坏零件。

★使用完毕后,关掉电源,将振动台面清洗干净。

Fourth, concrete vibration table instructions:
★ Before the installation of the vibrating table, the foundation should be laid. When the foundation is hit, the upper plane should be found horizontally and the fixing bolts should be buried according to the bolt holes of the bottom beam, and then installed. The fixing bolts must be tightened during installation.
★Before installing the vibrating table, drive for 3-5 minutes and then stop. Check all the fastening bolts. If it is loose, it must be tightened before use.
★ During the vibration table vibration, the concrete products should be firmly fastened on the vibration table. The required products should be placed symmetrically with the table top to balance the load. The fastening device of the vibrating product can be customized according to your own needs. Design and formulation.
★Vibrator bearings should be inspected frequently, and regularly removed and replaced, and the lubricant should be replaced to keep the bearings well lubricated and prolong the service life of the vibrators.
★ The vibration table should have a reliable grounding wire to ensure safety.

 

六,混凝土振实台调试与安装方法:

★吊运:

台面与底架两侧面有四只Φ40孔,为起吊孔,整机运输时,采用底架两侧面四只起吊孔,作为整机运输用。在拆卸台面时,采用台面两侧面四只起吊孔,应先将起重设备装置钩套入孔内,将台面提高约5cm,使活动台面与底架下的定位销脱离后,方可吊运台面。

★安装:

混凝土振动台在安装前应先将安装水泥基础上按“地脚螺栓位置尺寸图”位置浇埋妥四只M16地脚螺栓。水泥基础上平面必须校水平。然后填入消振橡胶垫层,在安装底架拧紧固定螺栓时要找正底架水平。在安装活动台面前,将硬性橡胶填入底架上部,台面与底架安装入座后,发现台面四角不平,可在未压紧的橡胶垫层处再垫入薄橡皮至台面四周均匀压紧为止

Sixth, concrete vibration table debugging and installation methods:
★ Lifting:
There are four Φ40 holes on the two sides of the table and the bottom frame. They are lifting holes. When transporting the whole machine, four lifting holes on the two sides of the bottom frame are used for the whole machine transportation. When disassembling the table top, use four lifting holes on both sides of the table. The lifting device should be hooked into the hole first, and the table surface should be raised by about 5cm so that the movable table and the positioning pin under the chassis can be lifted before lifting. mesa.
★Installation:
Before installing the concrete vibrating table, the four M16 anchor bolts should be buried on the foundation of the installed cement according to the position of the anchor bolt position. The plane must be leveled on the cement foundation. Then fill in the vibration-damping rubber cushion and find the level of the chassis when the mounting bracket is tightened. In front of the installation platform, the hard rubber is filled into the upper part of the bottom frame. After the table top and the bottom frame are installed in the seat, the four corners of the table are found to be uneven. The thin rubber can be placed on the unpressed rubber cushion layer until the table top is evenly pressed.

 

 


混凝土振实台

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号