STT-970通信管内壁静摩擦系数测试仪,通信管内壁静摩察系数

一、产品简介：

通信管内壁静摩擦系数测试仪是**检测仪器，是测量通信管内壁静摩察系数而设计和生产的，具有用性广、测量精度高、测量安全及可靠性好等特点。符合中华人民共和国交通行业标准JT/T496-2004《公路地下通信管道高密度聚乙烯硅芯塑料管》相关技术标准的要求。

Product introduction:

Communication tube inner wall static friction coefficient tester is a testing instrument designed and produced for measuring the static wall observation coefficient of communication tube inner wall. It has the characteristics of wide utility, high measurement accuracy, good measurement safety and reliability. It meets the requirements of the relevant technical standards of the People's Republic of China Transportation Industry Standard JT / T496-2004 "High-density polyethylene silicon core plastic pipes for highway underground communication pipelines".

二、技术参数：

♦测量范围：0°～45°

♦测量精度： 2.0′

♦试棒重量：270±10g

♦表层材料邵氏硬度：HD59±3

♦表面粗糙度R a 值：0.20μm～0.50μm

♦外形尺寸：600X750X1200mm

♦    重量:150kg

Technical parameters:

♦ Measurement range: 0 ° ～ 45 °

♦ Measurement accuracy: 2.0 ′

♦ Test rod weight: 270 ± 10g

♦ Shore hardness of surface material: HD59 ± 3

♦ Surface roughness R a value: 0.20μm ～ 0.50μm

♦ Overall dimensions: 600X750X1200mm

♦ Weight: 150kg

三、操作步骤：

♦ 将试样固定在V型铁上，从右端插入试棒使一端露出20mm，拴好链绳。

♦ 轻微摇动手轮使V型铁上水平泡处于水平位置。

♦ 打开角度尺紧固栓，转动角度尺使角度尺与副尺归零，拧紧紧固栓。

♦ 顺时针摇动手轮，使V型铁缓慢倾斜，直至试棒滑动为止。

♦ 记录下角度尺示值。

♦ 逆时针摇动手轮，使V型铁水平为止。

♦ 将试棒拉出通信管外露20mm。

♦ 按照以上操作步骤连续9次，计算出9次平均值。（倾斜角度≤14°4′依据JT/T683-2009《通信管道静摩擦系数测量仪》之规定要求）

Third, the operation steps:

♦ Fix the sample on the V-shaped iron, insert the test rod from the right end so that one end is exposed 20mm, and fasten the chain rope.

♦ Slightly shake the handwheel to make the horizontal bubble on the V-shaped iron in the horizontal position.

♦ Open the fastening pin of the angle ruler, turn the angle ruler to zero the angle ruler and the vice ruler, and tighten the fastening pin.

♦ Shake the handwheel clockwise to tilt the V-shaped iron slowly until the test rod slides.

♦ Record the displayed value of the angle ruler.

♦ Turn the handwheel counterclockwise until the V-shaped iron is level.

♦ Pull the test rod out of the communication tube to expose 20mm.

♦ Follow the above steps for 9 consecutive times and calculate the average of 9 times. (Tilt angle ≤14 ° 4 ′ according to the requirements of JT / T683-2009 "Communication Pipe Static Friction Coefficient Measuring Instrument")

四、结构组成：

主要由以下部分组成：

1、底座

2、手摇轮及传动杆

3、蜗轮蜗杆

4、上底版

5、角度尺及副尺

6、V型卡铁及水平装置固定夹

7、试棒及链绳

Fourth, the structural composition:

It is mainly composed of the following parts:

1.Base

2.Handwheel and transmission rod

3, worm gear

4, on the bottom plate

5.Angle ruler and vice ruler

6, V-shaped iron and horizontal device fixing clip

7, test rods and chains

五、贮存条件：

测定器及其附件应存放在干燥、清洁、无振动、无易燃、易腐蚀物品的环境条件下。

6. Storage conditions:

The analyzer and its accessories should be stored in a dry, clean, vibration-free, flammable, and corrosive environment.