上海荣计达仪器科技有限公司

021-61997300 13761118616

累积点滴改进  迈向完美品质

www.rongjida.cn

图片展示
搜索

GLM-200钢轮式耐磨试验机

采用了摆线针轮减速机,减速比大,结构紧凑,传动平稳,磨料流量可调,能有效地节约磨料的用量。该试验机通过齿轮传动减速达到钢轮转速75r/min,齿轮传动相比皮带传动减速精准、平稳、不会出现打滑现象,钢轮转动由时间继电器控制,电机转到预定时间也就是转到试验要求的转速,电机自动停止。该试验机具有设计合理、结构简单、造型美观、操作方便、转动平稳,达到试验要求自动停机等特点,主要适用用于水泥砖的耐磨试验。

  • 型号: GLM-200

  • 产品参数
  • 型号: GLM-200

一,产品简介:
采用了摆线针轮减速机,减速比大,结构紧凑,传动平稳,磨料流量可调,能有效地节约磨料的用量。该试验机通过齿轮传动减速达到钢轮转速75r/min,齿轮传动相比皮带传动减速精准、平稳、不会出现打滑现象,钢轮转动由时间继电器控制,电机转到预定时间也就是转到试验要求的转速,电机自动停止。该试验机具有设计合理、结构简单、造型美观、操作方便、转动平稳,达到试验要求自动停机等特点,主要适用用于水泥砖的耐磨试验。
First, product introduction
The cycloidal pinwheel reducer is adopted, the reduction ratio is large, the structure is compact, the transmission is stable, the abrasive flow rate is adjustable, and the amount of abrasive can be effectively saved. The test machine achieves the speed of the steel wheel by 75r/min through the gear transmission deceleration. The gear transmission is accurate and stable compared with the belt drive, and there is no slip phenomenon. The rotation of the steel wheel is controlled by the time relay, and the motor is transferred to the predetermined time. The required speed and the motor are automatically stopped. The testing machine has the characteristics of reasonable design, simple structure, beautiful appearance, convenient operation, stable rotation, automatic shutdown of the test requirements, and is mainly applicable to the abrasion resistance test of cement bricks.

二,技术参数:
磨轮一:直径200±0.2mm,厚度10±0.1mm,
磨轮二:直径200±0.2mm,厚度70±0.1mm,硬度HB203-245
磨轮转速:75±4r/min恒定;
试样尺寸:100mm ×110 mm;
磨料:粒度为ISO8486-1986中规定的F80白色熔融氧化铝;
磨料给入速度:(100±10)g/100r流量可调;
贮料斗容积:大于5L;
试验时间:可预置,数字显示;
砝码一:一质量为2.5㎏(适用GB/T3810.7-2006);
砝码二:一质量为14㎏(适用GB/ T12988-91)。
外形尺寸:6000x580x130mm
   重量:约150kg
Second, technical parameters
 Grinding wheel 1: diameter 200±0.2mm, thickness 10±0.1mm,
 Grinding wheel 2: diameter 200±0.2mm, thickness 70±0.1mm, hardness HB203-245
 Grinding wheel speed: 75±4r/min constant;
 Sample size: 100mm × 110 mm;
 Abrasive: F80 white fused alumina as specified in ISO 8486-1986;
 Abrasive feeding speed: (100±10)g/100r flow adjustable;
 Storage hopper volume: greater than 5L;
 Test time: preset, digital display;
 weight one: one mass is 2.5kg (applicable to GB/T3810.7-2006);
 Weight 2: One mass is 14kg (applicable to GB/T12988-91).
 Dimensions: 6000x580x130mm
 Weight: about 150kg

三,符合标准:
GB/T3810.7—2016《无釉砖耐磨试验方法》
ISO/DIS10545/6—94《无釉砖耐深度磨损试验方法》
GB/T12988-1009《无机地面材料耐磨试验方法》
Third, in line with the standard:
GB/T3810.7—2016 “Abrasion Test Method for Unglazed Bricks”
ISO/DIS10545/6-94 "Test method for deep wear resistance of unglazed bricks"
GB/T12988-1009 "Test method for abrasion resistance of inorganic floor materials"

四,注意事项及其保养:
接通电源线时,应注意电机正反转,钢轮应该按照箭头指示方向旋转;
试验机必须在接地标志处可靠接地(线径不小于1.5mm);
每次试验后,应将试验机打扫干净,尤其应将夹具及其导轨上的沙子清理干净;
每一年应将齿轮箱侧盖板卸下,在齿轮上加适量锂基润滑脂。
环境温度:室温
周围无腐蚀性性质
地面坚固水平
电源为380V,电压波动范围不超过额定电压的10%
Fourth, matters needing attention and maintenance
 When turning on the power cord, you should pay attention to the motor is reversed, and the steel wheel should rotate in the direction indicated by the arrow;
 The test machine must be reliably grounded at the grounding mark (wire diameter not less than 1.5mm);
 After each test, the test machine should be cleaned, especially the sand on the clamp and its guide rails should be cleaned;
 The gearbox side cover should be removed every year, and an appropriate amount of lithium grease should be added to the gear.
 Ambient temperature: room temperature
No corrosive properties around
 Ground level
 The power supply is 380V, and the voltage fluctuation range does not exceed 10% of the rated voltage.
 

 


GLM-200钢轮式耐磨试验机

长按图片可保存到相册

图片加载中,请稍等 ...
长按图片保存/分享
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

GLM-200钢轮式耐磨试验机

立即询盘
询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

推荐产品

上海荣计达仪器科技有限公司

电话:021-61997300

传真:021-34795918

邮箱:289239104@qq.com

地址:上海市闵行区浦江镇联胜路189号 

邮编:201112 

图片展示

版权所有:上海荣计达仪器科技有限   公司地址:上海市闵行区浦江镇联胜路189号 邮编:201112   沪ICP备11009963号