上海荣计达仪器科技有限公司

咨询电话:137-6111-8616


建筑涂料耐洗刷仪

该仪器是用来测定涂料涂层(表面状的)耐洗刷性能的仪器。有时还用来评价任何薄膜复合处理过的表面如:油漆、电镀、地板、罩面层、木材密度等形式表面的性能。该装置对涂刷于标准试板上的涂料行进洗刷。仪 器采用可编程控制,液晶屏显示,操作简单,具有信息断电保护功能。性能可靠,使用灵活方便。

  • 型号: JTX-II

  • 产品参数
  • 型号: JTX-II

一、产品简介:

该仪器是用来测定涂料涂层(表面状的)耐洗刷性能的仪器。有时还用来评价任何薄膜复合处理过的表面如:油漆、电镀、地板、罩面层、木材密度等形式表面的性能。该装置对涂刷于标准试板上的涂料行进洗刷。仪 器采用可编程控制,液晶屏显示,操作简单,具有信息断电保护功能。性能可靠,使用灵活方便。

Product introduction:

This instrument is used to determine the scrub resistance of paint coatings (surface-like). It is also sometimes used to evaluate the performance of any film composite treated surface such as: paint, electroplating, flooring, overlay, wood density and other forms of surface. The device scrubs the paint applied on the standard test plate. The instrument adopts programmable control, LCD screen display, simple operation, and information power protection function. Reliable performance, flexible and convenient to use.


二、技术参数:

♦刷子规格: 38X90mm的底板上均布60个Ф3孔穿zhu毛‚毛长19mm

♦刷子自重(包括刷具): 450±2g 

♦滴液速度:每秒钟滴加大约0.04g

♦刷子行程: 300mm

♦刷子运行频率: 37±1次/分

♦计数控制显示位数:5位

♦计数范围:99999次

♦试板尺寸:430X150X3mm

♦电机功率:25W

♦电源:220V 50HZ

♦外型尺寸:570X420X300mm

♦整机重量:32kg

Technical parameters:

Brush specifications: 60 Ф3 holes are worn on the 38X90mm floor, and the hair length is 19mm.

♦ Brush weight (including brush): 450 ± 2g

Dropping speed: about 0.04g per second

Brush stroke: 300mm

Brush running frequency: 37 ± 1 times / minute

♦ Counting control display digits: 5 digits

♦ Counting range: 99999 times

♦ Test plate size: 430X150X3mm

♦ Motor power: 25W

♦ Power supply: 220V 50HZ

♦ Overall dimensions: 570X420X300mm

♦ Whole machine weight: 32kg


三、使用方法:

♦预先将毛刷放在20°C的水中浸泡30分钟,浸泡深度为12mm,然后取出毛刷用力压干,再在0.5%的皂液中浸泡10分钟。

♦将试板放在工作盘内,将两发固定栓卡在试板边框上,拧紧螺母,使试件在工作过程中没有移动现象。

♦将刷子与刷具放在一起。放入平行滑架内即可。

♦将0.5%浓度的皂液放满储蓄槽,再把出水管插入水泵的出水口,打开总电源开关,打开泵电源开关(泵电源应联机在机身的插座上),出水管向试板输送皂液。送液量的大小可通过调节泵流量调节杆来控制。

♦按“设定”键(详见键盘操作说明),设定所需洗刷次数。一切工作**绪,按运行按钮,刷子开始运行,控制器进行加法计数。

♦观察试板中间10厘米处有无磨损现象及露底现象,中途欲停机,则按下“暂停”键,停止洗刷。

♦当试件未露底,实际计数值已达到设定值而停机时,如果继续实验,通过键盘操作,将实际计数值清零,再按运行按钮,计数器重新开始计数,累计实验结实。

♦如果用于检验产品,将设定值为为合格的洗刷次数,按运行“按钮”,当实际值等于设定值后自动停机,检查试板是否露底,以此判断产品是否合格。

Third, use method:

♦ Soak the brush in water at 20 ° C for 30 minutes in advance, soak the depth of 12mm, then take out the brush and press it dry, and soak it in 0.5% soap solution for 10 minutes.

♦ Place the test plate in the work plate, clamp the two bolts on the frame of the test plate, and tighten the nut so that the test piece does not move during the work.

♦ Put the brush and brush together. Just put it in the parallel carriage.

Fill the storage tank with 0.5% strength soap solution, then insert the outlet pipe into the water outlet of the pump, turn on the main power switch, turn on the pump power switch (the pump power should be connected to the socket of the body), and the outlet pipe goes to the test board. Transport soap. The amount of liquid delivered can be controlled by adjusting the pump flow adjustment lever.

♦ Press the “Set” key (see the keyboard operation instructions for details) to set the required number of scrubs. Everything works, press the run button, the brush starts running, and the controller counts up.

♦ Observe whether there is abrasion and exposed bottom at 10 cm in the middle of the test plate. If you want to stop the machine midway, press the "pause" button to stop scrubbing.

♦ When the test piece is not exposed and the actual count value has reached the set value and the machine stops, if you continue the experiment, clear the actual count value by keyboard operation, and then press the run button, the counter restarts counting and the cumulative experiment is solid.

♦ If it is used for product inspection, set the set value as the number of qualified scrubbing times and press the “button” to run. When the actual value is equal to the set value, it will automatically stop and check whether the test plate is exposed to determine whether the product is qualified.


四、产品特点:

♦该机采用了**的平行滑架,使刷子在工作过程中始终保持平行运行,重量恒定。克服了国内机型的卡刷,刷掉和摇摆现象。

♦采用新型线性往复机构,改进了国内机型的非线性往复运动,使300mm行程中刷洗均匀。

♦采用水泵自动循环送皂液系统,减轻了以往在运行过程中人工不断加皂液的工作,实现了自动化控制。本仪器采用64X128点阵液晶屏显示,显示清晰,操作方便,能显示传感器动态信息,具有数据储存断电记忆功能。

Fourth, product characteristics:

♦ The machine uses a ** parallel carriage to keep the brush running in parallel during the work, and the weight is constant. It overcomes the card swipe, swipe and swing phenomenon of domestic models.

♦ The new linear reciprocating mechanism is adopted to improve the non-linear reciprocating motion of domestic models and make the brushing uniform during the 300mm stroke.

♦ Adopting automatic circulating soap liquid delivery system by water pump, which reduces the work of manually adding soap liquid in the past during operation, and realizes automatic control. This instrument adopts 64X128 dot matrix LCD display, which is clear and easy to operate. It can display the dynamic information of the sensor and has the function of data storage and power failure memory.


五、注意事项:

♦使用前请将刷放在20℃的水浸泡30min,然后用力压干再在0.5%肥皂液中浸泡10min。

♦为保证试验数据的准确性和重现性请选择均匀一致的底材按同样的涂装工艺制备样品。

♦结果判定以试板中间长度100mm区域涂层破坏情况为依据。

♦当刷毛磨损至长度小于16mm时必须重新更换刷子。

Five, matters needing attention:

♦ Before use, please soak the brush in water at 20 ℃ for 30min, then dry it by pressing it hard and then soak it in 0.5% soap solution for 10min.

♦In order to ensure the accuracy and reproducibility of the test data, please choose a uniform substrate and prepare samples with the same coating process.

♦The results are judged based on the damage of the coating in the area of 100mm in the middle of the test plate.

♦When the bristles wear to less than 16mm, the brush must be replaced again.


建筑涂料耐洗刷仪
该仪器是用来测定涂料涂层(表面状的)耐洗刷性能的仪器。有时还用来评价任何薄膜复合处理过的表面如:油漆、电镀、地板、罩面层、木材密度等形式表面的性能。该装置对涂刷于标准试板上的涂料行进洗刷。仪 器采用可编程控制,液晶屏显示,操作简单,具有信息断电保护功能。性能可靠,使用灵活方便。
长按识别二维码查看详情
长按图片保存/分享

建筑涂料耐洗刷仪

询盘

咨询表单:

  • 请输入验证码

咨询产品:


你还没有添加任何产品!

扫一扫关注我们

Copyright @ 2018 上海荣计达仪器科技有限公司.All Rights Reserved   沪ICP备11009963号-4     

Copyright @ VillaGrandis All Rights Reserved某某某有限公司版权所有        

ICP备案号180006020号-3

 

客服中心
热线电话
13761118616
上班时间
周一到周日
二维码